Seagate ST3250824ACE, ST3120213ACE, ST3160212ACE, ST3200827ACE, ST3300822ACE Corrosive environment

Page 27

2.15Corrosive environment

Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM B845. However, this accelerated testing cannot duplicate every potential application environment. Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive chemicals as electronic drive component reliability can be affected by the installation environment. The silver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chlo- ride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulca- nized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.

DB35 Series 7200.2 Product Manual, Rev. C

21

Image 27
Contents DB35 Series Revision status summary sheet Contents DB35 Series 7200.2 Product Manual, Rev. C List of Figures DB35 Series 7200.2 Product Manual, Rev. C Introduction DB35 Series 7200.2 Product Manual, Rev. C Specification summary table Drive specificationsDrive specification ST3500841ACE ST3400833ACE Drive specifications for 500 and 400 Gbyte modelsFollowing web Drive specification ST3300822ACE ST3250824ACE ST3200827ACE Drive specifications for 300, 250, and 200 Gbyte modelsDB35 Series 7200.2 Product Manual, Rev. C Drive specification ST3160212ACE ST3120213ACE ST3802110ACE Drive specifications for 160, 120, and 80 Gbyte modelsAccess the following web Recording and interface technology Default logical geometryLBA mode Formatted capacityDB35 Series 7200.2 Product Manual, Rev. C Physical characteristics Seek timeStart/stop times Power specifications Typical current profile Conducted noiseVoltage tolerance Sleep mode Power-management modesActive mode Idle modeEnvironmental specifications Operating vibration AcousticsNonoperating shock VibrationElectromagnetic immunity ReliabilityRadio frequency environments Korean RRL Safety certificationAgency certification Electromagnetic compatibilityEnvironmental protection FCC verificationEuropean Union Restriction of Hazardous Substances RoHS Corrosive environment DB35 Series 7200.2 Product Manual, Rev. C Handling and static discharge precautions Configuring and mounting the driveBreather filter hole location Breather filter hole precautionsCable-select option Jumper settingsMaster/slave configuration Drive as master with a non-ATA-compatible slaveUltra ATA/100 cable Drive mountingMounting dimensions-top, side and end view DB35 Series 7200.2 Product Manual, Rev. C ATA interface ATA interface signals and connector pinsCommand name Command code in hex Supported ATA commandsF6H Write Sectors Without Retries 31H Write Sectors Extended 34H Word Description Value Identify Device commandXx07H Description if bit is set to Bit Word 0CH Set Features commandCode in features Register A.R.T. command 4 S.M.A.R.T. commandsDB35 Series 7200.2 Product Manual, Rev. C Presales Support Seagate Technology support servicesWarranty Service Internet MySeagate Spp.seagate.comData Recovery Services Data Recovery Services Authorized Service CentersFAX services-All Europe toll call Call center Presales and Technical Support Warranty ServiceToll-free support numbers Asia/Pacific support services Publication feedback survey DB35 Series 7200.2 Product Manual, Rev. C Numerics IndexPage Page DB35 Series 7200.2 Product Manual, Rev. C Page Seagate Technology LLC
Related manuals
Manual 52 pages 21.64 Kb