Seagate ST3500841ACE manual Jumper settings, Master/slave configuration, Cable-select option

Page 31

3.3Jumper settings

3.3.1Master/slave configuration

The options jumper block shown in Figure 4 is used to configure the drive for operation. It is the 8-pin dual header between the interface connector and the power connector. Use the following settings to configure the drive as a master or a slave.

Master or single drive. The drive is configured at the factory for a master or single-drive operation with a jumper set on pins 7 and 8.

Drive as slave. Remove all jumpers.

Drive as master with a non-ATA-compatible slave.

Use this jumper setting only if the drive does not work as a master with no jumpers installed.

Options jumper block

Master or single drive

Drive is slave

Master with non ATA- compatible slave

Cable select

Limit drive capacity to 32 Gbytes

7 5 3 1

8 6 4 2

Circuit Board

Figure 4 Master/slave jumper settings

3.3.2Cable-select option

Computers that use cable select determine the master and slave drives by selecting or deselecting pin 28, CSEL, on the interface bus. Master and slave drives are determined by their physical position on the cable. To enable cable select, set a jumper on pins 5 and 6 as shown in Figure 4. Refer to your computer manual to determine whether your computer supports this option.

3.3.3Alternate capacity jumper

Some older computers may “hang” at startup if their BIOS detects a disc drive with a capacity greater than 32 Gbytes. This limits the drive’s capacity to 32 Gbytes when the alternate capacity jumper is used. To access the full capacity of the drive, you can:

•Update the BIOS

•Use third-party software such as DiscWizard™ or Disk Manager

•Use a third-party host adapter

For drives with capacities greater than 32 Gbytes, the alternate capacity jumper changes the total available LBA sectors to 32 Gbytes to solve issues with some BIOS during power on. The ATA Set Features subcom- mand “F1H Report Full Capacity Available” causes Identify Data words 60 and 61 to report the full capacity. See Section 4.1.3 on page 36 for more details on the Set Features command.

DB35 Series 7200.2 Product Manual, Rev. C

25

Page 30 Page 32
Image 31
Page 30 Page 32
Contents DB35 Series Revision status summary sheet Contents DB35 Series 7200.2 Product Manual, Rev. C List of Figures DB35 Series 7200.2 Product Manual, Rev. C Introduction DB35 Series 7200.2 Product Manual, Rev. C Specification summary table Drive specificationsDrive specification ST3500841ACE ST3400833ACE Drive specifications for 500 and 400 Gbyte modelsFollowing web Drive specification ST3300822ACE ST3250824ACE ST3200827ACE Drive specifications for 300, 250, and 200 Gbyte modelsDB35 Series 7200.2 Product Manual, Rev. C Drive specification ST3160212ACE ST3120213ACE ST3802110ACE Drive specifications for 160, 120, and 80 Gbyte modelsAccess the following web Recording and interface technology Default logical geometryLBA mode Formatted capacityDB35 Series 7200.2 Product Manual, Rev. C Seek time Physical characteristicsStart/stop times Power specifications Conducted noise Typical current profileVoltage tolerance Sleep mode Power-management modesActive mode Idle modeEnvironmental specifications Operating vibration AcousticsNonoperating shock VibrationReliability Electromagnetic immunityRadio frequency environments Korean RRL Safety certificationAgency certification Electromagnetic compatibilityFCC verification Environmental protectionEuropean Union Restriction of Hazardous Substances RoHS Corrosive environment DB35 Series 7200.2 Product Manual, Rev. C Handling and static discharge precautions Configuring and mounting the driveBreather filter hole location Breather filter hole precautionsCable-select option Jumper settingsMaster/slave configuration Drive as master with a non-ATA-compatible slaveUltra ATA/100 cable Drive mountingMounting dimensions-top, side and end view DB35 Series 7200.2 Product Manual, Rev. C ATA interface ATA interface signals and connector pinsCommand name Command code in hex Supported ATA commandsF6H Write Sectors Without Retries 31H Write Sectors Extended 34H Word Description Value Identify Device commandXx07H Description if bit is set to Bit Word 0CH Set Features commandCode in features Register A.R.T. command 4 S.M.A.R.T. commandsDB35 Series 7200.2 Product Manual, Rev. C Presales Support Seagate Technology support servicesWarranty Service Internet MySeagate Spp.seagate.comData Recovery Services Data Recovery Services Authorized Service CentersCall center Presales and Technical Support Warranty Service FAX services-All Europe toll callToll-free support numbers Asia/Pacific support services Publication feedback survey DB35 Series 7200.2 Product Manual, Rev. C Numerics IndexPage Page DB35 Series 7200.2 Product Manual, Rev. C Page Seagate Technology LLC
Related manuals
Manual 52 pages 21.64 Kb
Top Page Image Contents