Seagate ST3146756SS (FDE) Relative humidity, Effective altitude sea level, Shock and vibration

Page 41

6.4.2Relative humidity

The values below assume that no condensation on the drive occurs.

a.Operating

5% to 95% non-condensing relative humidity with a maximum gradient of 20% per hour.

b.Non-operating

5% to 95% non-condensing relative humidity.

6.4.3Effective altitude (sea level)

a.Operating

–1,000 to +10,000 feet (–305 to +3,048 meters)

b.Non-operating

–1,000 to +40,000 feet (–305 to +12,210 meters)

6.4.4Shock and vibration

Shock and vibration limits specified in this document are measured directly on the drive chassis. If the drive is installed in an enclosure to which the stated shock and/or vibration criteria is applied, resonances may occur internally to the enclosure resulting in drive movement in excess of the stated limits. If this situation is apparent, it may be necessary to modify the enclosure to minimize drive movement.

The limits of shock and vibration defined within this document are specified with the drive mounted by any of the four methods shown in Figure 11, and in accordance with the restrictions of Section 8.3.

6.4.4.1Shock

a.Operating—normal

The drive, as installed for normal operation, shall operate error free while subjected to intermittent shock not exceeding:

•15 Gs at a duration of 11 msec (half sinewave)

•25 Gs at a duration of 2 msec (half sinewave)

•60 Gs at a duration of 2 msec (half sinewave) when performing reads only

Shock may be applied in the X, Y, or Z axis. Shock is not to be repeated more than once every 2 seconds.

b.Operating—abnormal

Equipment, as installed for normal operation, does not incur physical damage while subjected to intermit- tent shock not exceeding 40 Gs at a duration of 11 msec (half sinewave). Shock occurring at abnormal lev- els may promote degraded operational performance during the abnormal shock period. Specified operational performance will continue when normal operating shock levels resume. Shock may be applied in the X, Y, or Z axis. Shock is not to be repeated more than once every 2 seconds.

c.Non-operating

The limits of non-operating shock shall apply to all conditions of handling and transportation. This includes both isolated drives and integrated drives.

The drive subjected to nonrepetitive shock not exceeding the three values below, shall not exhibit device damage or performance degradation.

•80 Gs at a duration of 11 msec (half sinewave)

•300 Gs at a duration of 2 msec (half sinewave)

•150 Gs at a duration of 0.5 msec (half sinewave)

Shock may be applied in the X, Y, or Z axis.

Cheetah 15K.6 SAS Product Manual, Rev. B

37

Page 40 Page 42
Image 41
Page 40 Page 42
Contents ST3146356SS ST3450856SSST3300656SS Page Contents Installation Defect and error managementSeagate Technology support services Interface requirementsModel Number Full Disk Encryption FDE ScopeCheetah 15K.6 SAS Product Manual, Rev. B Standards Standards, compliance and reference documentsElectromagnetic compatibility Electromagnetic susceptibilityEuropean Union Restriction of Hazardous Substances RoHS ComplianceReference documents Cheetah 15K.6 SAS Product Manual, Rev. B General description Performance Standard featuresMedia description Reliability Factory-installed optionsFormatted capacities Programmable drive capacityCheetah 15K.6 SAS Product Manual, Rev. B Internal drive characteristics Performance characteristicsAccess time Seek timeGeneral performance characteristics Format command execution time minutesStart/stop time 176 144 100Cache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataError rates Reliability specificationsRecoverable Errors Unrecoverable ErrorsSeek errors Reliability and serviceInterface errors Preventive maintenanceControlling S.M.A.R.T 4 S.M.A.R.TPerformance impact MillisecondsDetermining rate Reporting controlPredictive failures Thermal monitorState of the drive prior to testing Temperature Log Page 0Dh Parameter Code DescriptionDrive Self Test DST DST failure definitionShort and extended tests Invoking DSTShort test Function Code 001b Extended test Function Code 010bAbort Product warrantyShipping Product repair and return informationCheetah 15K.6 SAS Product Manual, Rev. B AC power requirements Physical/electrical specificationsDC power requirements ST3450856SS DC power requirementsST3300656SS DC power requirements ST3450056SS FDE DC power requirementsST3450056SS FDE Gbit mode Amps ST3300656SS Gbit mode AmpsST3146356SS DC power requirements ST3300056SS FDE DC power requirementsST3300056SS FDE Gbit mode Amps ST3146356SS Gbit mode AmpsST3146756SS FDE Gbit mode Amps ST3146756SS FDE DC power requirementsCurrent profiles Power sequencingConducted noise immunity Typical 450GB current profiles Typical 146GB current profiles ST3450856SS model Power dissipationST3450056SS FDE model ST3300656SS model ST3300056SS FDE model ST3146356SS model ST3146756SS FDE model in 3 Gbit operation Environmental limits TemperatureEffective altitude sea level Relative humidityShock and vibration ShockRecommended mounting Package size Packaged/product weight Drop heightVibration Air cleanlinessAcoustics Corrosive environmentMechanical specifications Physical dimensions Cheetah 15K.6 SAS Product Manual, Rev. B Drive error recovery procedures Defect and error managementDrive internal defects/errors 51.87 Media Pre-Scan SAS system errorsBackground Media Scan Idle Read After Write Deferred Auto-ReallocationCooling InstallationDrive orientation Air flow Grounding Drive mountingCheetah 15K.6 SAS Product Manual, Rev. B Interface requirements SAS featuresDual port support Command name Command code Supported Scsi commands supportedCommands supported by Cheetah 15K.6 SAS family drives Commands supported by Cheetah 15K.6 SAS family drives Commands supported by Cheetah 15K.6 SAS family drives Commands supported by Cheetah 15K.6 SAS family drives Bytes Data hex Inquiry dataMode Sense data Mode Pages 2.1 ST3450856SS/ST3450056SS Mode Sense data2.2 ST3300656SS/ST3300056SS Mode Sense data 2.3 ST3146356SS/ST3146756SS Mode Sense data Miscellaneous features Miscellaneous operating features and conditionsMiscellaneous status SAS physical interfacePhysical interface Datum B Connector requirements Physical characteristicsElectrical description Pin Signal name Signal typePin descriptions SAS pin descriptionsPower Signal characteristicsSAS transmitters and receivers Ready LED OutDifferential signals LED drive signalGeneral interface characteristics Eye masks Eye masks overviewJitter tolerance masks Receive eye maskAbsolute amplitude Normalized time in UISinusoidal Peak-toJitter Frequency in kHzSignal characteristica Units Gbps Transmitter signal characteristicsMaximum allowable jitter Receiver signal characteristicsSignal characteristic Units Gbps Receiver jitter tolerance Impedance specificationsCompliant jitter test pattern Cjtpat Impedance requirements Sheet 1Electrical TxRx connections Transmitter characteristicsImpedance requirements Sheet 2 = -5,437dB Shows the zero-length test load Receiver characteristics Cheetah 15K.6 SAS Product Manual, Rev. B Internet Seagate Technology support servicesPresales Support Technical SupportData Recovery Services Call Center Toll-free Direct dial Warranty ServiceData Recovery Services Authorized Service Centers Numerics IndexIraw SAS See also cooling
Top Page Image Contents