Seagate ST3300656SS Temperature Log Page 0Dh, Parameter Code Description, Primary Temperature

Page 25

be used to set this trip point. The default value for this drive is 68°C, however, you can set it to any value in the range of 0 to 68°C. If you specify a temperature greater than 68°C in this field, the temperature is rounded down to 68°C. A sense code is sent to the host to indicate the rounding of the parameter field.

Table 1:

Temperature Log Page (0Dh)

 

 

Parameter Code

Description

 

 

 

0000h

 

Primary Temperature

 

 

 

0001h

 

Reference Temperature

 

 

 

5.2.6Drive Self Test (DST)

Drive Self Test (DST) is a technology designed to recognize drive fault conditions that qualify the drive as a failed unit. DST validates the functionality of the drive at a system level.

There are two test coverage options implemented in DST:

1.Extended test

2.Short text

The most thorough option is the extended test that performs various tests on the drive and scans every logical block address (LBA) of the drive. The short test is time-restricted and limited in length—it does not scan the entire media surface, but does some fundamental tests and scans portions of the media.

If DST encounters an error during either of these tests, it reports a fault condition. If the drive fails the test, remove it from service and return it to Seagate for service.

5.2.6.1DST failure definition

The drive will present a “diagnostic failed” condition through the self-tests results value of the diagnostic log page if a functional failure is encountered during DST. The channel and servo parameters are not modified to test the drive more stringently, and the number of retries are not reduced. All retries and recovery processes are enabled during the test. If data is recoverable, no failure condition will be reported regardless of the number of retries required to recover the data.

The following conditions are considered DST failure conditions:

•Seek error after retries are exhausted

•Track-follow error after retries are exhausted

•Read error after retries are exhausted

•Write error after retries are exhausted

Recovered errors will not be reported as diagnostic failures.

5.2.6.2Implementation

This section provides all of the information necessary to implement the DST function on this drive.

Cheetah 15K.6 SAS Product Manual, Rev. A

19

Page 24 Page 26
Image 25
Page 24 Page 26
Contents ST3450856SS ST3300656SS ST3146356SS Cheetah 15K.6 SASPage Contents Installation Defect and error managementSeagate Technology support services Interface requirementsCheetah 15K.6 SAS disk drive List of FiguresCheetah 15K.6 SAS Product Manual, Rev. a Cheetah 15K.6 SAS disk drive ScopeCheetah 15K.6 SAS Product Manual, Rev. a Standards Standards, compliance and reference documentsElectromagnetic compatibility Electromagnetic susceptibilityEuropean Union Restriction of Hazardous Substances RoHS ComplianceReference documents Cheetah 15K.6 SAS Product Manual, Rev. a General description Media description Standard featuresPerformance Options factory installed Factory-installed accessoriesReliability Formatted capacitiesCheetah 15K.6 SAS Product Manual, Rev. a Internal drive characteristics Performance characteristicsAccess time Seek timeGeneral performance characteristics Format command execution time minutesStart/stop time Cache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataError rates Reliability specificationsRecoverable Errors Unrecoverable ErrorsSeek errors Reliability and serviceInterface errors Preventive maintenanceControlling S.M.A.R.T 4 S.M.A.R.TPerformance impact MillisecondsDetermining rate Reporting controlPredictive failures Thermal monitorPrimary Temperature Temperature Log Page 0DhReference Temperature Parameter Code DescriptionInvoking DST State of the drive prior to testingShort and extended tests Short test Function Code 001bAbort Product warrantyShipping Product repair and return informationCheetah 15K.6 SAS Product Manual, Rev. a AC power requirements Physical/electrical specificationsDC power requirements ST3450856SS DC power requirementsST3146356SS DC power requirements ST3300656SS DC power requirementsST3300656SS Gbit mode Amps ST3146356SS Gbit mode AmpsPower sequencing General DC power requirement notesConducted noise immunity Current profilesTypical ST3450856SS current profiles Typical ST3300656SS current profiles Typical ST3146356SS current profiles ST3450856SS in 3 Gbit operation Power dissipationST3300656SS in 3 Gbit operation ST3300656SS CURRENT/POWER vs Throughput SAS 3.0GBST3146356SS in 3 Gbit operation ST3146356SS CURRENT/POWER vs Throughput SAS 3.0GBRandom 8 Block Reads Environmental limits TemperatureEffective altitude sea level Relative humidityShock and vibration ShockRecommended mounting Package size Packaged/product weight Drop heightVibration Air cleanlinessAcoustics Corrosive environmentMechanical specifications Physical dimensions Cheetah 15K.6 SAS Product Manual, Rev. a Drive internal defects/errors Defect and error managementDrive error recovery procedures 51.87 Background Media Scan SAS system errorsMedia Pre-Scan Idle Read After Write Deferred Auto-ReallocationDrive orientation InstallationAir flow CoolingGrounding Drive mountingCheetah 15K.6 SAS Product Manual, Rev. a Interface requirements SAS featuresDual port support Commands supported by Cheetah 15K.6 SAS family drives Scsi commands supportedCommand name Command code Supported Commands supported by Cheetah 15K.6 SAS family drives Commands supported by Cheetah 15K.6 SAS family drives Commands supported by Cheetah 15K.6 SAS family drives Inquiry data Mode Sense dataBytes Data hex Page Mode Pages 2.1 ST3450856SS Mode Sense data2.2 ST3300656SS Mode Sense data 2.3 ST3146356SS Mode Sense data Miscellaneous features Miscellaneous operating features and conditionsSupported Feature or condition Miscellaneous statusSAS physical interface Datum B Connector requirements Physical characteristicsElectrical description Pin Signal name Signal typePin descriptions SAS pin descriptionsPower Signal characteristicsSAS transmitters and receivers Ready LED OutDifferential signals LED drive signalGeneral interface characteristics Eye masks Eye masks overviewJitter tolerance masks Receive eye maskAbsolute amplitude Normalized time in UISinusoidal Peak-toJitter Frequency in kHzSignal characteristica Units Gbps Transmitter signal characteristicsSignal characteristic Units Gbps Receiver signal characteristicsMaximum allowable jitter Gbps m, n Deterministic jitterqReceiver jitter tolerance Impedance specificationsCompliant jitter test pattern Cjtpat Impedance requirements Sheet 1Impedance requirements Sheet 2 Transmitter characteristicsElectrical TxRx connections = -5,437dB Shows the zero-length test load Receiver characteristics Cheetah 15K.6 SAS Product Manual, Rev. a Internet Seagate Technology support servicesPresales Support Technical SupportData Recovery Services Authorized Service Centers Warranty ServiceData Recovery Services Call Center Toll-free Direct dial Numerics IndexPage SAS See also cooling
Top Page Image Contents