Seagate ST3300656SS, ST3146356SS General DC power requirement notes, Conducted noise immunity

Page 31

15,000 RPM. The ±5% must be maintained after the drive signifies that its power-up sequence has been completed and that the drive is able to accept selection by the host initiator.

[3]See +12V current profile in Figure 2.

[4]This condition occurs after OOB and Speed Negotiation completes but before the drive has received the Notify Spinup primitive.

[5]See paragraph 6.2.1, "Conducted noise immunity." Specified voltage tolerance includes ripple, noise, and transient response.

[6]Operating condition is defined as random 8 block reads at 330 I/Os per second for ST3450856SS and 347 I/Os per second for ST3300656SS and ST3146356SS models. Current and power specified at nomi- nal voltages.

[7]During idle, the drive heads are relocated every 60 seconds to a random location within the band from three-quarters to maximum track.

General DC power requirement notes.

1.Minimum current loading for each supply voltage is not less than 1.7% of the maximum operating current shown.

2.The +5V and +12V supplies should employ separate ground returns.

3.Where power is provided to multiple drives from a common supply, careful consideration for individual drive power requirements should be noted. Where multiple units are powered on simultaneously, the peak starting current must be available to each device.

4.Parameters, other than spindle start, are measured after a 10-minute warm up.

5.No terminator power.

6.2.1Conducted noise immunity

Noise is specified as a periodic and random distribution of frequencies covering a band from DC to 10 MHz. Maximum allowed noise values given below are peak-to-peak measurements and apply at the drive power connector.

+5V

=

250 mV pp from 0 to

100 kHz to 20 MHz.

+12V

=

800 mV pp from 100

Hz to 8 KHz.

 

 

450 mV pp from 8 KHz to 20 KHz.

 

 

250 mV pp from 20 KHz to 5 MHz.

6.2.2Power sequencing

The drive does not require power sequencing. The drive protects against inadvertent writing during power-up and down.

6.2.3Current profiles

The +12V and +5V current profiles for ST3450856SS, ST3300656SS and ST3146356SS models are shown below in the following figures.

Note: All times and currents are typical. See Tables 2, 3, and 4 for maximum current requirements.

Cheetah 15K.6 SAS Product Manual, Rev. A

25

Page 30 Page 32
Image 31
Page 30 Page 32
Contents ST3450856SS ST3300656SS ST3146356SS Cheetah 15K.6 SASPage Contents Interface requirements Defect and error managementInstallation Seagate Technology support servicesCheetah 15K.6 SAS disk drive List of FiguresCheetah 15K.6 SAS Product Manual, Rev. a Cheetah 15K.6 SAS disk drive ScopeCheetah 15K.6 SAS Product Manual, Rev. a Electromagnetic susceptibility Standards, compliance and reference documentsStandards Electromagnetic compatibilityEuropean Union Restriction of Hazardous Substances RoHS ComplianceReference documents Cheetah 15K.6 SAS Product Manual, Rev. a General description Media description Standard featuresPerformance Formatted capacities Factory-installed accessoriesOptions factory installed ReliabilityCheetah 15K.6 SAS Product Manual, Rev. a Seek time Performance characteristicsInternal drive characteristics Access timeGeneral performance characteristics Format command execution time minutesStart/stop time Cache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataUnrecoverable Errors Reliability specificationsError rates Recoverable ErrorsPreventive maintenance Reliability and serviceSeek errors Interface errorsMilliseconds 4 S.M.A.R.TControlling S.M.A.R.T Performance impactThermal monitor Reporting controlDetermining rate Predictive failuresParameter Code Description Temperature Log Page 0DhPrimary Temperature Reference TemperatureShort test Function Code 001b State of the drive prior to testingInvoking DST Short and extended testsProduct repair and return information Product warrantyAbort ShippingCheetah 15K.6 SAS Product Manual, Rev. a ST3450856SS DC power requirements Physical/electrical specificationsAC power requirements DC power requirementsST3146356SS Gbit mode Amps ST3300656SS DC power requirementsST3146356SS DC power requirements ST3300656SS Gbit mode AmpsCurrent profiles General DC power requirement notesPower sequencing Conducted noise immunityTypical ST3450856SS current profiles Typical ST3300656SS current profiles Typical ST3146356SS current profiles ST3450856SS in 3 Gbit operation Power dissipationST3300656SS in 3 Gbit operation ST3300656SS CURRENT/POWER vs Throughput SAS 3.0GBST3146356SS in 3 Gbit operation ST3146356SS CURRENT/POWER vs Throughput SAS 3.0GBRandom 8 Block Reads Environmental limits TemperatureShock Relative humidityEffective altitude sea level Shock and vibrationRecommended mounting Package size Packaged/product weight Drop heightCorrosive environment Air cleanlinessVibration AcousticsMechanical specifications Physical dimensions Cheetah 15K.6 SAS Product Manual, Rev. a Drive internal defects/errors Defect and error managementDrive error recovery procedures 51.87 Background Media Scan SAS system errorsMedia Pre-Scan Idle Read After Write Deferred Auto-ReallocationDrive orientation InstallationAir flow CoolingGrounding Drive mountingCheetah 15K.6 SAS Product Manual, Rev. a Interface requirements SAS featuresDual port support Commands supported by Cheetah 15K.6 SAS family drives Scsi commands supportedCommand name Command code Supported Commands supported by Cheetah 15K.6 SAS family drives Commands supported by Cheetah 15K.6 SAS family drives Commands supported by Cheetah 15K.6 SAS family drives Inquiry data Mode Sense dataBytes Data hex Page Mode Pages 2.1 ST3450856SS Mode Sense data2.2 ST3300656SS Mode Sense data 2.3 ST3146356SS Mode Sense data Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features Supported Feature or conditionSAS physical interface Datum B Connector requirements Physical characteristicsSAS pin descriptions Pin Signal name Signal typeElectrical description Pin descriptionsReady LED Out Signal characteristicsPower SAS transmitters and receiversEye masks Eye masks overview LED drive signalDifferential signals General interface characteristicsNormalized time in UI Receive eye maskJitter tolerance masks Absolute amplitudeFrequency in kHz Peak-toSinusoidal JitterSignal characteristica Units Gbps Transmitter signal characteristicsGbps m, n Deterministic jitterq Receiver signal characteristicsSignal characteristic Units Gbps Maximum allowable jitterImpedance requirements Sheet 1 Impedance specificationsReceiver jitter tolerance Compliant jitter test pattern CjtpatImpedance requirements Sheet 2 Transmitter characteristicsElectrical TxRx connections = -5,437dB Shows the zero-length test load Receiver characteristics Cheetah 15K.6 SAS Product Manual, Rev. a Technical Support Seagate Technology support servicesInternet Presales SupportData Recovery Services Authorized Service Centers Warranty ServiceData Recovery Services Call Center Toll-free Direct dial Numerics IndexPage SAS See also cooling
Top Page Image Contents