Seagate ST3300656SS, ST3146356SS, ST3450856SS manual Receiver characteristics

Page 79

9.5.2.5Receiver characteristics

The drive receiver is A.C. coupled. The receive network terminates the TxRx connection by a 100 ohm equiva- lent impedance as specified in table 20.

The receiver operates within a BER of 10-12when a SAS signal with valid voltage and timing characteristics is delivered to the compliance point from a 100 ohm source. The received SAS signal are considered valid if it meets the voltage and timing limits specified in table 17.

Additionally the receiver operates within the BER objective when the signal at a receiving phy has the addi- tional sinusoidal jitter present that is specified in table 19 and the common mode signal VCM over frequency range FCM as specified in table 15. The jitter tolerance is shown in Figure 19 for all Rx compliance points in a TxRx connection. The figure given assumes that any external interference occurs prior to the point at which the test is applied. When testing the jitter tolerance capability of a receiver, the additional 0.1 UI of sinusoidal jitter may be reduced by an amount proportional to the actual externally induced interference between the applica- tion point of the test and the input to the receiving phy. The additional jitter reduces the eye opening in both voltage and time.

Cheetah 15K.6 SAS Product Manual, Rev. A

73

Image 79

Contents ST3450856SS ST3300656SS ST3146356SS Cheetah 15K.6 SASPage Contents Interface requirements Defect and error managementInstallation Seagate Technology support servicesCheetah 15K.6 SAS disk drive List of FiguresCheetah 15K.6 SAS Product Manual, Rev. a Cheetah 15K.6 SAS disk drive ScopeCheetah 15K.6 SAS Product Manual, Rev. a Electromagnetic susceptibility Standards, compliance and reference documentsStandards Electromagnetic compatibilityEuropean Union Restriction of Hazardous Substances RoHS ComplianceReference documents Cheetah 15K.6 SAS Product Manual, Rev. a General description Media description Standard featuresPerformance Formatted capacities Factory-installed accessoriesOptions factory installed ReliabilityCheetah 15K.6 SAS Product Manual, Rev. a Seek time Performance characteristicsInternal drive characteristics Access timeGeneral performance characteristics Format command execution time minutesStart/stop time Cache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataUnrecoverable Errors Reliability specificationsError rates Recoverable ErrorsPreventive maintenance Reliability and serviceSeek errors Interface errorsMilliseconds 4 S.M.A.R.TControlling S.M.A.R.T Performance impactThermal monitor Reporting controlDetermining rate Predictive failuresParameter Code Description Temperature Log Page 0DhPrimary Temperature Reference TemperatureShort test Function Code 001b State of the drive prior to testingInvoking DST Short and extended testsProduct repair and return information Product warrantyAbort ShippingCheetah 15K.6 SAS Product Manual, Rev. a ST3450856SS DC power requirements Physical/electrical specificationsAC power requirements DC power requirementsST3146356SS Gbit mode Amps ST3300656SS DC power requirementsST3146356SS DC power requirements ST3300656SS Gbit mode AmpsCurrent profiles General DC power requirement notesPower sequencing Conducted noise immunityTypical ST3450856SS current profiles Typical ST3300656SS current profiles Typical ST3146356SS current profiles ST3450856SS in 3 Gbit operation Power dissipationST3300656SS in 3 Gbit operation ST3300656SS CURRENT/POWER vs Throughput SAS 3.0GBST3146356SS in 3 Gbit operation ST3146356SS CURRENT/POWER vs Throughput SAS 3.0GBRandom 8 Block Reads Environmental limits TemperatureShock Relative humidityEffective altitude sea level Shock and vibrationRecommended mounting Package size Packaged/product weight Drop heightCorrosive environment Air cleanlinessVibration AcousticsMechanical specifications Physical dimensions Cheetah 15K.6 SAS Product Manual, Rev. a Drive internal defects/errors Defect and error managementDrive error recovery procedures 51.87 Background Media Scan SAS system errorsMedia Pre-Scan Idle Read After Write Deferred Auto-ReallocationDrive orientation InstallationAir flow CoolingGrounding Drive mountingCheetah 15K.6 SAS Product Manual, Rev. a Interface requirements SAS featuresDual port support Commands supported by Cheetah 15K.6 SAS family drives Scsi commands supportedCommand name Command code Supported Commands supported by Cheetah 15K.6 SAS family drives Commands supported by Cheetah 15K.6 SAS family drives Commands supported by Cheetah 15K.6 SAS family drives Inquiry data Mode Sense dataBytes Data hex Page Mode Pages 2.1 ST3450856SS Mode Sense data2.2 ST3300656SS Mode Sense data 2.3 ST3146356SS Mode Sense data Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features Supported Feature or conditionSAS physical interface Datum B Connector requirements Physical characteristicsSAS pin descriptions Pin Signal name Signal typeElectrical description Pin descriptionsReady LED Out Signal characteristicsPower SAS transmitters and receiversEye masks Eye masks overview LED drive signalDifferential signals General interface characteristicsNormalized time in UI Receive eye maskJitter tolerance masks Absolute amplitudeFrequency in kHz Peak-toSinusoidal JitterSignal characteristica Units Gbps Transmitter signal characteristicsGbps m, n Deterministic jitterq Receiver signal characteristicsSignal characteristic Units Gbps Maximum allowable jitterImpedance requirements Sheet 1 Impedance specificationsReceiver jitter tolerance Compliant jitter test pattern CjtpatImpedance requirements Sheet 2 Transmitter characteristicsElectrical TxRx connections = -5,437dB Shows the zero-length test load Receiver characteristics Cheetah 15K.6 SAS Product Manual, Rev. a Technical Support Seagate Technology support servicesInternet Presales SupportData Recovery Services Authorized Service Centers Warranty ServiceData Recovery Services Call Center Toll-free Direct dial Numerics IndexPage SAS See also cooling