Seagate ST3146356SS Standards, compliance and reference documents, Electromagnetic compatibility

Page 9

2.0Standards, compliance and reference documents

The drive has been developed as a system peripheral to the highest standards of design and construction. The drive depends on its host equipment to provide adequate power and environment for optimum performance and compliance with applicable industry and governmental regulations. Special attention must be given in the areas of safety, power distribution, shielding, audible noise control, and temperature regulation. In particular, the drive must be securely mounted to guarantee the specified performance characteristics. Mounting by bot- tom holes must meet the requirements of Section 8.3.

2.1Standards

The Cheetah SAS family complies with Seagate standards as noted in the appropriate sections of this manual and the Seagate SAS Interface Manual, part number 100293071.

The Cheetah disk drive is a UL recognized component per UL1950, CSA certified to CAN/CSA C22.2 No. 950- 95, and VDE certified to VDE 0805 and EN60950.

2.1.1Electromagnetic compatibility

The drive, as delivered, is designed for system integration and installation into a suitable enclosure prior to use. The drive is supplied as a subassembly and is not subject to Subpart B of Part 15 of the FCC Rules and Regulations nor the Radio Interference Regulations of the Canadian Department of Communications.

The design characteristics of the drive serve to minimize radiation when installed in an enclosure that provides reasonable shielding. The drive is capable of meeting the Class B limits of the FCC Rules and Regulations of the Canadian Department of Communications when properly packaged; however, it is the user’s responsibility to assure that the drive meets the appropriate EMI requirements in their system. Shielded I/O cables may be required if the enclosure does not provide adequate shielding. If the I/O cables are external to the enclosure, shielded cables should be used, with the shields grounded to the enclosure and to the host controller.

2.1.1.1Electromagnetic susceptibility

As a component assembly, the drive is not required to meet any susceptibility performance requirements. It is the responsibility of those integrating the drive within their systems to perform those tests required and design their system to ensure that equipment operating in the same system as the drive or external to the system does not adversely affect the performance of the drive. See Tables 2, 3 and 4, for DC power requirements.

Cheetah 15K.6 SAS Product Manual, Rev. A

3

Page 8 Page 10
Image 9
Page 8 Page 10
Contents ST3450856SS ST3300656SS ST3146356SS Cheetah 15K.6 SASPage Contents Installation Defect and error managementSeagate Technology support services Interface requirementsCheetah 15K.6 SAS disk drive List of FiguresCheetah 15K.6 SAS Product Manual, Rev. a Cheetah 15K.6 SAS disk drive ScopeCheetah 15K.6 SAS Product Manual, Rev. a Standards Standards, compliance and reference documentsElectromagnetic compatibility Electromagnetic susceptibilityEuropean Union Restriction of Hazardous Substances RoHS ComplianceReference documents Cheetah 15K.6 SAS Product Manual, Rev. a General description Standard features Media descriptionPerformance Options factory installed Factory-installed accessoriesReliability Formatted capacitiesCheetah 15K.6 SAS Product Manual, Rev. a Internal drive characteristics Performance characteristicsAccess time Seek timeFormat command execution time minutes General performance characteristicsStart/stop time Cache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataError rates Reliability specificationsRecoverable Errors Unrecoverable ErrorsSeek errors Reliability and serviceInterface errors Preventive maintenanceControlling S.M.A.R.T 4 S.M.A.R.TPerformance impact MillisecondsDetermining rate Reporting controlPredictive failures Thermal monitorPrimary Temperature Temperature Log Page 0DhReference Temperature Parameter Code DescriptionInvoking DST State of the drive prior to testingShort and extended tests Short test Function Code 001bAbort Product warrantyShipping Product repair and return informationCheetah 15K.6 SAS Product Manual, Rev. a AC power requirements Physical/electrical specificationsDC power requirements ST3450856SS DC power requirementsST3146356SS DC power requirements ST3300656SS DC power requirementsST3300656SS Gbit mode Amps ST3146356SS Gbit mode AmpsPower sequencing General DC power requirement notesConducted noise immunity Current profilesTypical ST3450856SS current profiles Typical ST3300656SS current profiles Typical ST3146356SS current profiles ST3450856SS in 3 Gbit operation Power dissipationST3300656SS in 3 Gbit operation ST3300656SS CURRENT/POWER vs Throughput SAS 3.0GBST3146356SS CURRENT/POWER vs Throughput SAS 3.0GB ST3146356SS in 3 Gbit operationRandom 8 Block Reads Environmental limits TemperatureEffective altitude sea level Relative humidityShock and vibration ShockRecommended mounting Package size Packaged/product weight Drop heightVibration Air cleanlinessAcoustics Corrosive environmentMechanical specifications Physical dimensions Cheetah 15K.6 SAS Product Manual, Rev. a Defect and error management Drive internal defects/errorsDrive error recovery procedures 51.87 SAS system errors Background Media ScanMedia Pre-Scan Idle Read After Write Deferred Auto-ReallocationDrive orientation InstallationAir flow CoolingGrounding Drive mountingCheetah 15K.6 SAS Product Manual, Rev. a Interface requirements SAS featuresDual port support Scsi commands supported Commands supported by Cheetah 15K.6 SAS family drivesCommand name Command code Supported Commands supported by Cheetah 15K.6 SAS family drives Commands supported by Cheetah 15K.6 SAS family drives Commands supported by Cheetah 15K.6 SAS family drives Mode Sense data Inquiry dataBytes Data hex Page Mode Pages 2.1 ST3450856SS Mode Sense data2.2 ST3300656SS Mode Sense data 2.3 ST3146356SS Mode Sense data Miscellaneous features Miscellaneous operating features and conditionsSupported Feature or condition Miscellaneous statusSAS physical interface Datum B Connector requirements Physical characteristicsElectrical description Pin Signal name Signal typePin descriptions SAS pin descriptionsPower Signal characteristicsSAS transmitters and receivers Ready LED OutDifferential signals LED drive signalGeneral interface characteristics Eye masks Eye masks overviewJitter tolerance masks Receive eye maskAbsolute amplitude Normalized time in UISinusoidal Peak-toJitter Frequency in kHzSignal characteristica Units Gbps Transmitter signal characteristicsSignal characteristic Units Gbps Receiver signal characteristicsMaximum allowable jitter Gbps m, n Deterministic jitterqReceiver jitter tolerance Impedance specificationsCompliant jitter test pattern Cjtpat Impedance requirements Sheet 1Transmitter characteristics Impedance requirements Sheet 2Electrical TxRx connections = -5,437dB Shows the zero-length test load Receiver characteristics Cheetah 15K.6 SAS Product Manual, Rev. a Internet Seagate Technology support servicesPresales Support Technical SupportWarranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Numerics IndexPage SAS See also cooling
Top Page Image Contents