Western Telematic PLS-345 manual Circuit Status Screen

Page 15

Section 3: Quick Start / System Overview

Physical Layer Switch v1.00				Site ID:	PLS-345_TEST_IRVINE_CALIFORNIA
CKT#		From	To		POS MON Default
-----+		------------------	+------------------		+	-----	+	-----	+	---------
1		PORT_11111111111 PORT_BBBBBBBBBBB				B				A
2		PORT_22222222222 PORT_AAAAAAAAAAA				A		*		A
3		PORT_33333333333 PORT_AAAAAAAAAAA				A		*		A
-----+		------------------	+------------------		+	-----	+	-----	+	---------
Command Echo:			On
Inactivity Timeout:			30	Min
Command Confirmation:			On
Automated Mode:			Off
Monitor Mode:			On
Monitor Input Level:			1 - High

"/H" for help.

PLS>

Figure 3.1: The Circuit Status Screen

b)Modem Access: Start your communications program, and dial the number for the external modem. The PLS Circuit Status Screen (Figure 3.1) should be displayed, followed by the PLS> command prompt.

c)Console Port Access (Local PC): Start your communication program, make certain the communications program is set for the PC COM port that is attached to the PLS, and then press [Enter]. The PLS Circuit Status Screen (Figure 3.1) should be displayed, followed by the PLS> command prompt.

5.Review Help Menu: At the PLS> command prompt, Type /H and press [Enter] to display a help menu (Figure 3.2), which provides a basic listing of PLS commands.

3-3

Image 15

Contents PLS-345 Page Shock Hazard Do Not Enter Nameplate Power WarningVentilation Enclosed RacksTable of Contents Application Examples Command SummaryIntroduction Monitor ModeApplications Typographic ConventionsFront Panel Unit DescriptionBack Panel Back PanelUnit Description PLS-345 Physical Layer Switch Users Guide Quick Start / System Overview $ telnet 192.168.168.168 Enter Modem & Console Port Access Factory set PLSCircuit Status Screen Command Help Screen System Mode Installation Power Supply ConnectionInitialization Connecting a PC to the Console Port Connecting Common and A/B LinesConnecting the Network Cable Connecting an External ModemSystem Mode and User Mode SetUp and ConfigurationCommunicating with the PLS-345 SetUp and Configuration PLS Command/Menu Conventions Defining General Parameters SetUp and ConfigurationPLS-345 Physical Layer Switch Users Guide SetUp and Configuration Circuit Parameters Menu Circuit ParametersNetwork Parameters Network Parameters Menu IP Security Implementing IP SecurityExample 1 Deny access to all hosts except Monitor Mode Hardware ConfigurationSelecting Monitor Mode Parameters Monitor Mode Parameters Menu Switch if Level 1 High Switch to Position B Return On Save Configuration Parameters Circuit Status Screen Status ScreensPLS-345 Physical Layer Switch Users Guide Port Network Status ScreenPLS-345 Physical Layer Switch Users Guide Operation Manual A/B SwitchingEnter Code Activated A/B Switching/A Command and the /B Command Enter or /B n EnterCommand Confirmation Prompt /D CommandMonitor Mode Sending Parameters to a File Saving and Restoring Configuration ParametersRestoring Saved Parameters Application Examples Monitoring Signal Drop and/or Power LossAUX Port Connection Monitoring a Contact Monitoring a Switch or RelayItem 6 Circuits to Switch Enable the Monitor Mode at circuit Display Circuit Status Command SummaryDisplay Commands Display Help ScreenView/Set Circuit Parameters Configuration CommandsSN Display Network Status View/Set General ParametersView/Set Monitor Mode Parameters DL Download Configuration to FileView/Set Network Parameters Control Commands Switch Circuit n to Line aSwitch Circuit n to Line B Command Format /T Enter Command Arguments Set Circuits to DefaultReset Network Interface Command Format /D Enter Command ArgumentsExit/Disconnect Command Format /X Enter Command ArgumentsInterface Descriptions Console Port InterfaceModem Port Interface Figure A.3 Common Ports and A/B Ports Common Ports and A/B PortsSpecifications SwitchingSize Trademark and Copyright Information Customer ServiceIndex Index-2 Page Sterling Irvine California 949 586-9950 Toll Free