Western Telematic PLS-345 manual Specifications, Switching, Size

Page 57

Appendices

B.Specifications

Interface: RJ-45, three jacks, Cat5 compliant, capable of switching 10/100Base-T with minimum dB loss, 8 pins switched, Common Jack to "A" or "B" Jack.

Contacts: High reliability, mechanical relays, break-before- make contacts with 1 amp @ 30 VDC rating, 100 million cycle life.

Switching:

Manual: Individual or ALL from front panel controls.

Code: By circuit number or name.

Network Port: 10BaseT Ethernet, RJ45.

Console Port: RS-232, DB-9M, DTE pinout.

Coding: Serial ASCII, 8 bits, no parity.

Data Rate: 2400, 9600, 19.2K, 38.4K bps.

Modem Port: RS-232, DB-9M, DTE pinout. Sends auto-setup command strings (user definable.)

Memory: Non-volatile parameter storage.

Size:

Height: 1.75" (4.4 cm), 1 Rack Unit.

Width: 19.00" (48.3 cm) with rack mounting.

Depth: 6.75" (17.2 cm)

Shipping Weight: 6.0 Lbs. (2.7 kg.)

Power: IEC-320 inlet, 100/240 VAC, 50/60 Hz, 5 Watts.

Operating Temperature: 32￿F to 122￿F (0￿C to 50￿C.)

Humidity: 10 to 90% RH.

Apx-3

Image 57
Contents PLS-345 Page Shock Hazard Do Not Enter Nameplate Power WarningVentilation Enclosed RacksTable of Contents Application Examples Command SummaryIntroduction Monitor ModeApplications Typographic ConventionsFront Panel Unit DescriptionBack Panel Back PanelUnit Description PLS-345 Physical Layer Switch Users Guide Quick Start / System Overview $ telnet 192.168.168.168 Enter Modem & Console Port Access Factory set PLSCircuit Status Screen Command Help Screen System Mode Installation Power Supply ConnectionInitialization Connecting the Network Cable Connecting Common and A/B LinesConnecting an External Modem Connecting a PC to the Console PortSystem Mode and User Mode SetUp and ConfigurationCommunicating with the PLS-345 SetUp and Configuration PLS Command/Menu Conventions Defining General Parameters SetUp and ConfigurationPLS-345 Physical Layer Switch Users Guide SetUp and Configuration Circuit Parameters Menu Circuit ParametersNetwork Parameters Network Parameters Menu IP Security Implementing IP SecurityExample 1 Deny access to all hosts except Monitor Mode Hardware ConfigurationSelecting Monitor Mode Parameters Monitor Mode Parameters Menu Switch if Level 1 High Switch to Position B Return On Save Configuration Parameters Circuit Status Screen Status ScreensPLS-345 Physical Layer Switch Users Guide Port Network Status ScreenPLS-345 Physical Layer Switch Users Guide Operation Manual A/B Switching/A Command and the /B Command Code Activated A/B SwitchingEnter or /B n Enter EnterCommand Confirmation Prompt /D CommandMonitor Mode Sending Parameters to a File Saving and Restoring Configuration ParametersRestoring Saved Parameters Application Examples Monitoring Signal Drop and/or Power LossAUX Port Connection Monitoring a Contact Monitoring a Switch or RelayItem 6 Circuits to Switch Enable the Monitor Mode at circuit Display Commands Command SummaryDisplay Help Screen Display Circuit StatusSN Display Network Status Configuration CommandsView/Set General Parameters View/Set Circuit ParametersView/Set Monitor Mode Parameters DL Download Configuration to FileView/Set Network Parameters Control Commands Switch Circuit n to Line aSwitch Circuit n to Line B Reset Network Interface Set Circuits to DefaultCommand Format /D Enter Command Arguments Command Format /T Enter Command ArgumentsExit/Disconnect Command Format /X Enter Command ArgumentsInterface Descriptions Console Port InterfaceModem Port Interface Figure A.3 Common Ports and A/B Ports Common Ports and A/B PortsSpecifications SwitchingSize Trademark and Copyright Information Customer ServiceIndex Index-2 Page Sterling Irvine California 949 586-9950 Toll Free