Tyan Computer InterServe 90 manual Pri/Sec Master/Slave Armd Emulated as, 1st Boot Device

Page 48

Chapter 4

BIOS Configuration

Pri/Sec Master/Slave ARMD Emulated as

ATAPI Removable Media Disks (e.g. ZIP drives) are hybrid drives. They are removable, and can be used as floppy drives, but also have great capacity and so are sometimes used as hard drives. These four options ensure that, if you have an ARMD attached as a master or slave device, it can be properly detected by the system. The settings are Auto, Floppy, and Hard Disk.

1st Boot Device

This option sets the type of device for the first boot drive that the AMIBIOS attempts to boot from after AMIBIOS POST completes. The settings are Disabled, 1st IDE-HDD, 2nd IDE-HDD, 3rd IDE-HDD, 4th IDE-HDD, Floppy, ARMD-FDD, ARMD-HDD, ATAPI CDROM, SCSI, NETWORK, and I2O.

2nd Boot Device

This option sets the type of device for the second boot drive that the AMIBIOS attempts to boot from after AMIBIOS POST completes. The settings are Disabled, 1st IDE-HDD, 2nd IDE-HDD, 3rd IDE-HDD, 4th IDE-HDD, Floppy, ARMD-FDD, ARMD-HDD, ATAPI CDROM, and SCSI.

3rd Boot Device

This option sets the type of device for the third boot drive that the AMIBIOS attempts to boot from after AMIBIOS POST completes. The settings are Disabled, 1st IDE-HDD, 2nd IDE-HDD, 3rd IDE-HDD, 4th IDE-HDD, Floppy,

ARMD-FDD, ARMD-HDD, ATAPI CDROM.

Try Other Boot Devices

Set this option to Yes to instruct AMIBIOS to attempt to boot from any other drive in the system if it cannot find a boot drive among the drives specified in the 1st Boot Device, 2nd Boot Device, and 3rd Boot Device options. The settings are Yes or No.

Floppy Access Control

This option specifies the read-write access that is set when booting from a floppy drive. The settings are Read-Write or Read-Only.

Hard Disk Access Control

This option specifies the read-write access that is set when booting from a hard disk drive. The settings are Read-Write or Read-Only.

S.M.A.R.T. for Hard Disks

Set this option to Enabled to permit AMIBIOS to use the SMART (System

http://www.tyan.com

46

Image 48

Contents InterServe Pins ErrataTyan S1832DL Tiger Table of Contents System Resources Appendix 1 CPU Retention Module Options Appendix 2 GlossaryChapter OverviewIcons Hardware Specifications/Features Physical Dimensions Bios InformationDisk Drive & System I/O Software Specifications Technical SupportAlt.comp.periphs.mainboard.tyan 510Returning Merchandise for Service For Resellers OnlyInstallation UnpackingInstall the motherboard into your case What’s the first thing I should do?Plug in the power connector as shown Conforms to industry standard revisionPin Chapter Next are the Com and Printer ports Connecting the USB and PS/2 ports Installing your add-in cards is relatively simple but Shows the USB ports and the PS/2 portsNext, you need to install your memory Install Finally, install your CPU Installing CPU Retention Modules Installing the Active ProcessorActive Passive Chapter Installing the Passive Processor Setting Jumpers Removing the CPUYou are done Pin jumpers Or more pin jumpers Off OpenThis page has been intentionally left blank Onboard Resource Settings Quick References for JumpersMap of Motherboard Jumpers PS/2 ports COM2 LPT1 COM1 USB ports LM79 PCI slots CPU Settings for 66MHz Bus CPU Settings for 100MHz Bus2x9 External Connector Proprietary Server Mgmt Connector J10 External Pin AssignmentsSoft Power Connector Speaker Connector InstallationHardware Reset Switch Connector Installation Chassis Intrusion Alarm Connector Flash EepromWindows 95 Users Hardware Cmos & Password Reset RAM InstallationCache Memory DimmFrequently Asked Questions Pin DimmChapter This page has been intentionally left blank Bios Configuration Main Setup Key FunctionSystem Date/Time Floppy Drive a and BType How to Configure Entering Drive Parameters Parameter DescriptionBoot Sector Virus Protection Optimal DefaultsFail-Safe Defaults Auto-Detect Hard DisksAdvanced Cmos Setup Advanced Cmos Setup Default Settings ChartSettings Chart Quick Boot1st Boot Device 2nd Boot Device3rd Boot Device Try Other Boot DevicesBoot Up Num-Lock Password CheckBoot To OS/2 System Bios CacheableDefault Primary Video Cache Bus ECCMPS Revision C000,16K Shadow and C400,16K ShadowChipset Setup Advanced Chipset Setup EnterUSB Function AGP S E R RBX Master Latency Timer Clks Multi-Trans Timer ClksUSB KB/Mouse Legacy Support Port 64/60 EmulationPCI1 to PCI0 Access Dram Integrity ModeSetting Description Sdram RAS# to CAS# DelayAGP Multi-Trans Timer AGP Clks AGP Low-Priority Timer ClksAGP Parity Error Response 8bit I/O Recovery Time16bit I/O Recovery Time USB Passive ReleasePIIX4 Passive Release TypeF DMA Buffer Control1Power Management Setup Power Management Setup EnterPower Management/APM Power Button FunctionGreen PC Monitor Power State Acpi Aware O/SVideo Power Down Mode Hard Disk Power Down ModePower Saving Type Standby/Suspend Timer UnitPC98 Power LED Slow Clock RatioDisplay Activity LAN Wake-upPlug and Play Setup RTC Wake-upPlug and Play Setup Default Settings Chart PCI Latency Timer PCI Clocks Plug and Play Aware O/SPCI VGA Palette Snoop Allocate IRQ to PCI VGAOffBoard PCI IDE Primary IRQ Offboard PCI IDE Secondary IRQPCI Slot n IRQ Priority DMA Channel nBios Devnode for Shadow RAM Reserved Memory AddressPCI Device Search Order Peripheral Setup Peripheral Setup Default Settings ChartDefault Settings Chart Power InterruptionSerial Port2 Mode Overclock Warning MessageIR Transmission Mode Mode DescriptionParallel Port Mode IR Receiver PinParallel Port IRQ Parallel Port DMA ChannelOnboardIDE Supervisor and User Security Language Utility Flash Writer UtilitySystem Resources Beep CodesTroubleshooting System Problems If the computer beeps ThenDisplayed Error Messages Error Message ExplanationError Message Explanation OFF Board Parity Error Addr =Appendix Option Glossary Page Appendix Page Appendix Page Appendix Document # D1308-210