Tyan Computer InterServe 90 manual Plug and Play Setup, RTC Wake-up

Page 61

RTC Wake-up

If Enabled, this option allows you to set an hour and minute for the system to wake up. The next two fields allow you to choose the wake up time. Note that the time fields will not be available if this option is set to Disabled. In order for this wake up function to work, the system must have been brought up at least past the POST before it was last shut down (i.e. if you turn the system off before the POST, the registry will not be set, and the system will not be able to wake up using this function). The settings are Enabled or Disabled.

3.5 Plug and Play Setup

Choose PCI/Plug and Play Setup from the AMIBIOS Setup screen to display the PCI and Plug and Play Setup options, described below.

AMI BIOS EASY SETUP UTILITY Ver.1.16

(c)1998 American Megatrends, Inc. All Rights Reserved

Advanced

Advanced CMOS Setup			[ Enter ]	Setup Help
Advanced Chipset Setup			[ Enter ]
Power Management Setup			[ Enter ]	Configure PCI / Plug
	Plug and Play Setup		[ Enter ]	and Play features
	Peripheral Setup		[ Enter ]
Change Language Setting			English

- Previous Item ¯ Next Item

¬® Select Menu

ESC:Exit Enter:Select F5:Setup Defaults F6:Original Values F10:Save & Exit

http://www.tyan.com

BIOS

59

Image 61

Contents InterServe Errata PinsTyan S1832DL Tiger Table of Contents Appendix 1 CPU Retention Module Options Appendix 2 Glossary System ResourcesOverview ChapterIcons Hardware Specifications/Features Bios Information Physical DimensionsDisk Drive & System I/O Technical Support Software SpecificationsAlt.comp.periphs.mainboard.tyan 510For Resellers Only Returning Merchandise for ServiceUnpacking InstallationWhat’s the first thing I should do? Install the motherboard into your caseConforms to industry standard revision Plug in the power connector as shownPin Chapter Next are the Com and Printer ports Connecting the USB and PS/2 ports Shows the USB ports and the PS/2 ports Installing your add-in cards is relatively simple butNext, you need to install your memory Install Finally, install your CPU Installing the Active Processor Installing CPU Retention ModulesActive Passive Chapter Installing the Passive Processor Removing the CPU Setting JumpersYou are done Pin jumpers Or more pin jumpers Off OpenThis page has been intentionally left blank Quick References for Jumpers Onboard Resource SettingsMap of Motherboard Jumpers PS/2 ports COM2 LPT1 COM1 USB ports LM79 PCI slots CPU Settings for 100MHz Bus CPU Settings for 66MHz BusJ10 External Pin Assignments 2x9 External Connector Proprietary Server Mgmt ConnectorSpeaker Connector Installation Soft Power ConnectorHardware Reset Switch Connector Installation Flash Eeprom Chassis Intrusion Alarm ConnectorWindows 95 Users RAM Installation Hardware Cmos & Password ResetDimm Cache MemoryPin Dimm Frequently Asked QuestionsChapter This page has been intentionally left blank Bios Configuration Key Function Main SetupFloppy Drive a and B System Date/TimeType How to Configure Parameter Description Entering Drive ParametersOptimal Defaults Boot Sector Virus ProtectionFail-Safe Defaults Auto-Detect Hard DisksAdvanced Cmos Setup Default Settings Chart Advanced Cmos SetupQuick Boot Settings Chart2nd Boot Device 1st Boot Device3rd Boot Device Try Other Boot DevicesPassword Check Boot Up Num-LockBoot To OS/2 System Bios CacheableCache Bus ECC Default Primary VideoMPS Revision C000,16K Shadow and C400,16K ShadowAdvanced Chipset Setup Enter Chipset SetupAGP S E R R USB FunctionMulti-Trans Timer Clks BX Master Latency Timer ClksUSB KB/Mouse Legacy Support Port 64/60 EmulationDram Integrity Mode PCI1 to PCI0 AccessSetting Description Sdram RAS# to CAS# DelayAGP Low-Priority Timer Clks AGP Multi-Trans Timer AGP ClksAGP Parity Error Response 8bit I/O Recovery TimeUSB Passive Release 16bit I/O Recovery TimePIIX4 Passive Release TypeF DMA Buffer Control1Power Management Setup Enter Power Management SetupPower Button Function Power Management/APMGreen PC Monitor Power State Acpi Aware O/SHard Disk Power Down Mode Video Power Down ModePower Saving Type Standby/Suspend Timer UnitSlow Clock Ratio PC98 Power LEDDisplay Activity LAN Wake-upRTC Wake-up Plug and Play SetupPlug and Play Setup Default Settings Chart Plug and Play Aware O/S PCI Latency Timer PCI ClocksPCI VGA Palette Snoop Allocate IRQ to PCI VGAOffboard PCI IDE Secondary IRQ OffBoard PCI IDE Primary IRQPCI Slot n IRQ Priority DMA Channel nReserved Memory Address Bios Devnode for Shadow RAMPCI Device Search Order Peripheral Setup Default Settings Chart Peripheral SetupPower Interruption Default Settings ChartSerial Port2 Mode Overclock Warning MessageMode Description IR Transmission ModeParallel Port Mode IR Receiver PinParallel Port DMA Channel Parallel Port IRQOnboardIDE Supervisor and User Security Flash Writer Utility Language UtilityBeep Codes System ResourcesIf the computer beeps Then Troubleshooting System ProblemsError Message Explanation Displayed Error MessagesOFF Board Parity Error Addr = Error Message ExplanationAppendix Option Glossary Page Appendix Page Appendix Page Appendix Document # D1308-210