Tyan Computer InterServe 90 manual Appendix

Page 82

Appendix 2

Glossary

details for you.

ISA stands for Industry Standard Architecture. ISA is a slower 8- or 16-bit BUS (data pathway).

Latency is the amount of time that one part of a system spends waiting for another part to catch up. This is most common when the system sends data out to a peripheral device, and is waiting for the peripheral to send some data back (peripherals tend to be slower than onboard system components).

NVRAM ROM and EEPROM are both examples of Non-Volatile RAM, memory that holds its data without power. DRAM, in contrast, is volatile.

OEMs (Original Equipment Manufacturers) like Compaq or IBM package other companies’ motherboards and hardware inside their case and sell them.

The parallel port transmits the bits of a byte on eight different wires at the same time (that is, in parallel form, eight bits at the same time).

PCI stands for Peripheral Component Interconnect. PCI is a 32-bit local bus (data pathway) which is faster than the ISA bus. Local buses are those which operate within a single system (as opposed to a network bus, which connects multiple systems).

The PCI PIO (PCI Programmable Input/Output) modes are the data transfer modes used by IDE drives. These modes use the CPU for data transfer (DMA channels do not). PCI refers to the type of bus used by these modes to communicate with the CPU.

PCI-to-PCI bridge allows you to connect multiple PCI devices onto one PCI slot.

Pipeline burst SRAM is a fast secondary cache. It is used as a secondary cache because SRAM is slower than SDRAM, but usually larger. Data is cached first to the faster primary cache, and then, when the primary cache is full, to the slower secondary cache.

Pipelining improves system performance by allowing the CPU to begin executing a second instruction before the first is completed. A pipeline can be likened to an assembly line, with a given part of the pipeline repeatedly executing a set part of an operation on a series of instructions.

http://www.tyan.com

80

Image 82
Contents InterServe Pins ErrataTyan S1832DL Tiger Table of Contents System Resources Appendix 1 CPU Retention Module Options Appendix 2 GlossaryChapter OverviewIcons Hardware Specifications/Features Bios Information Physical DimensionsDisk Drive & System I/O Alt.comp.periphs.mainboard.tyan Software SpecificationsTechnical Support 510Returning Merchandise for Service For Resellers OnlyInstallation UnpackingInstall the motherboard into your case What’s the first thing I should do?Plug in the power connector as shown Conforms to industry standard revisionPin Chapter Next are the Com and Printer ports Connecting the USB and PS/2 ports Installing your add-in cards is relatively simple but Shows the USB ports and the PS/2 portsNext, you need to install your memory Install Finally, install your CPU Installing the Active Processor Installing CPU Retention ModulesActive Passive Chapter Installing the Passive Processor You are done Setting JumpersRemoving the CPU Pin jumpers Or more pin jumpers Off OpenThis page has been intentionally left blank Onboard Resource Settings Quick References for JumpersMap of Motherboard Jumpers PS/2 ports COM2 LPT1 COM1 USB ports LM79 PCI slots CPU Settings for 66MHz Bus CPU Settings for 100MHz Bus2x9 External Connector Proprietary Server Mgmt Connector J10 External Pin AssignmentsSpeaker Connector Installation Soft Power ConnectorHardware Reset Switch Connector Installation Flash Eeprom Chassis Intrusion Alarm ConnectorWindows 95 Users Hardware Cmos & Password Reset RAM InstallationCache Memory DimmFrequently Asked Questions Pin DimmChapter This page has been intentionally left blank Bios Configuration Main Setup Key FunctionSystem Date/Time Floppy Drive a and BType How to Configure Entering Drive Parameters Parameter DescriptionFail-Safe Defaults Boot Sector Virus ProtectionOptimal Defaults Auto-Detect Hard DisksAdvanced Cmos Setup Advanced Cmos Setup Default Settings ChartSettings Chart Quick Boot3rd Boot Device 1st Boot Device2nd Boot Device Try Other Boot DevicesBoot To OS/2 Boot Up Num-LockPassword Check System Bios CacheableMPS Revision Default Primary VideoCache Bus ECC C000,16K Shadow and C400,16K ShadowChipset Setup Advanced Chipset Setup EnterUSB Function AGP S E R RUSB KB/Mouse Legacy Support BX Master Latency Timer ClksMulti-Trans Timer Clks Port 64/60 EmulationSetting Description PCI1 to PCI0 AccessDram Integrity Mode Sdram RAS# to CAS# DelayAGP Parity Error Response AGP Multi-Trans Timer AGP ClksAGP Low-Priority Timer Clks 8bit I/O Recovery TimePIIX4 Passive Release 16bit I/O Recovery TimeUSB Passive Release TypeF DMA Buffer Control1Power Management Setup Power Management Setup EnterGreen PC Monitor Power State Power Management/APMPower Button Function Acpi Aware O/SPower Saving Type Video Power Down ModeHard Disk Power Down Mode Standby/Suspend Timer UnitDisplay Activity PC98 Power LEDSlow Clock Ratio LAN Wake-upPlug and Play Setup RTC Wake-upPlug and Play Setup Default Settings Chart PCI VGA Palette Snoop PCI Latency Timer PCI ClocksPlug and Play Aware O/S Allocate IRQ to PCI VGAPCI Slot n IRQ Priority OffBoard PCI IDE Primary IRQOffboard PCI IDE Secondary IRQ DMA Channel nReserved Memory Address Bios Devnode for Shadow RAMPCI Device Search Order Peripheral Setup Peripheral Setup Default Settings ChartSerial Port2 Mode Default Settings ChartPower Interruption Overclock Warning MessageParallel Port Mode IR Transmission ModeMode Description IR Receiver PinParallel Port DMA Channel Parallel Port IRQOnboardIDE Supervisor and User Security Language Utility Flash Writer UtilitySystem Resources Beep CodesTroubleshooting System Problems If the computer beeps ThenDisplayed Error Messages Error Message ExplanationError Message Explanation OFF Board Parity Error Addr =Appendix Option Glossary Page Appendix Page Appendix Page Appendix Document # D1308-210