Tyan Computer InterServe 90 manual Peripheral Setup Default Settings Chart

Page 66

Chapter 4

BIOS Configuration

3.6 Peripheral Setup

Peripheral Setup options are displayed by choosing Peripheral Setup from the AMIBIOS Setup main menu. All Peripheral Setup options are described here.

AMI BIOS EASY SETUP UTILITY Ver.1.16

(c)1998 American Megatrends, Inc. All Rights Reserved

Advanced

Advanced CMOS Setup [ Enter ] Advanced Chipset Setup [ Enter ] Power Management Setup [ Enter ] Plug and Play Setup [ Enter ] Peripheral Setup [ Enter ] Change Language Setting English

Setup Help

Configure PCI / Plug and Play features

- Previous Item ¯ Next Item

¬® Select Menu

ESC:Exit Enter:Select F5:Setup Defaults F6:Original Values F10:Save & Exit

Peripheral Setup Default Settings Chart

Setting Option	Optimal Default	Fail-Safe Default

P ower Interruption	Dis abled	Dis abled

Overclock Warning Mes s age	E nabled	E nabled

LM79 IN0	2.06	2.06

LM79 IN1	2.04	2.04

LM79 IN2	3.32	3.32

LM79 IN3	5.16	5.16

LM79 IN4	11.91	11.91

LM79 IN5	-11.81	-11.81

LM79 IN6	-5.13	-5.13

OnboardF DC	Auto	Auto

OnboardS erial P ort 1	3F 8h	3F 8h

OnboardS erial P ort 2	2F 8h	2F 8h

S erial P ort 2 Mode	Normal	Normal

*IR Duplex Mode	N/A	N/A

http://www.tyan.com

64

Image 66

Contents InterServe Pins ErrataTyan S1832DL Tiger Table of Contents System Resources Appendix 1 CPU Retention Module Options Appendix 2 GlossaryChapter OverviewIcons Hardware Specifications/Features Physical Dimensions Bios InformationDisk Drive & System I/O Alt.comp.periphs.mainboard.tyan Software SpecificationsTechnical Support 510Returning Merchandise for Service For Resellers OnlyInstallation UnpackingInstall the motherboard into your case What’s the first thing I should do?Plug in the power connector as shown Conforms to industry standard revisionPin Chapter Next are the Com and Printer ports Connecting the USB and PS/2 ports Installing your add-in cards is relatively simple but Shows the USB ports and the PS/2 portsNext, you need to install your memory Install Finally, install your CPU Installing CPU Retention Modules Installing the Active ProcessorActive Passive Chapter Installing the Passive Processor You are done Setting JumpersRemoving the CPU Pin jumpers Or more pin jumpers Off OpenThis page has been intentionally left blank Onboard Resource Settings Quick References for JumpersMap of Motherboard Jumpers PS/2 ports COM2 LPT1 COM1 USB ports LM79 PCI slots CPU Settings for 66MHz Bus CPU Settings for 100MHz Bus2x9 External Connector Proprietary Server Mgmt Connector J10 External Pin AssignmentsSoft Power Connector Speaker Connector InstallationHardware Reset Switch Connector Installation Chassis Intrusion Alarm Connector Flash EepromWindows 95 Users Hardware Cmos & Password Reset RAM InstallationCache Memory DimmFrequently Asked Questions Pin DimmChapter This page has been intentionally left blank Bios Configuration Main Setup Key FunctionSystem Date/Time Floppy Drive a and BType How to Configure Entering Drive Parameters Parameter DescriptionFail-Safe Defaults Boot Sector Virus ProtectionOptimal Defaults Auto-Detect Hard DisksAdvanced Cmos Setup Advanced Cmos Setup Default Settings ChartSettings Chart Quick Boot3rd Boot Device 1st Boot Device2nd Boot Device Try Other Boot DevicesBoot To OS/2 Boot Up Num-LockPassword Check System Bios CacheableMPS Revision Default Primary VideoCache Bus ECC C000,16K Shadow and C400,16K ShadowChipset Setup Advanced Chipset Setup EnterUSB Function AGP S E R RUSB KB/Mouse Legacy Support BX Master Latency Timer ClksMulti-Trans Timer Clks Port 64/60 EmulationSetting Description PCI1 to PCI0 AccessDram Integrity Mode Sdram RAS# to CAS# DelayAGP Parity Error Response AGP Multi-Trans Timer AGP ClksAGP Low-Priority Timer Clks 8bit I/O Recovery TimePIIX4 Passive Release 16bit I/O Recovery TimeUSB Passive Release TypeF DMA Buffer Control1Power Management Setup Power Management Setup EnterGreen PC Monitor Power State Power Management/APMPower Button Function Acpi Aware O/SPower Saving Type Video Power Down ModeHard Disk Power Down Mode Standby/Suspend Timer UnitDisplay Activity PC98 Power LEDSlow Clock Ratio LAN Wake-upPlug and Play Setup RTC Wake-upPlug and Play Setup Default Settings Chart PCI VGA Palette Snoop PCI Latency Timer PCI ClocksPlug and Play Aware O/S Allocate IRQ to PCI VGAPCI Slot n IRQ Priority OffBoard PCI IDE Primary IRQOffboard PCI IDE Secondary IRQ DMA Channel nBios Devnode for Shadow RAM Reserved Memory AddressPCI Device Search Order Peripheral Setup Peripheral Setup Default Settings ChartSerial Port2 Mode Default Settings ChartPower Interruption Overclock Warning MessageParallel Port Mode IR Transmission ModeMode Description IR Receiver PinParallel Port IRQ Parallel Port DMA ChannelOnboardIDE Supervisor and User Security Language Utility Flash Writer UtilitySystem Resources Beep CodesTroubleshooting System Problems If the computer beeps ThenDisplayed Error Messages Error Message ExplanationError Message Explanation OFF Board Parity Error Addr =Appendix Option Glossary Page Appendix Page Appendix Page Appendix Document # D1308-210