Tyan Computer InterServe 90 manual

Page 83

PM timers (Power Management timers) are software timers that count down the number of seconds or minutes until the system times out and enters sleep, suspend, or doze mode.

PnP is an acronym for Plug and Play, a design standard that has become ascendant in the industry. Plug and Play devices require little set-up to use. Novice end users can simply plug them into a computer that is running on a Plug and Play-aware operating system (such as Windows 95), and go to work. Devices and operating systems that are not Plug and Play require you to reconfigure your system each time you add or change any part of your hardware.

The term RAM (Random Access Memory), while technically referring to a type of memory where any byte can be accessed without touching the adjacent data, is often used to refer to the system’s main memory. This memory is available to any program running on the computer.

ROM (Read-Only Memory) is a storage chip which contains the BIOS (Basic Input/Output System), the basic instructions required to boot the computer and start up the operating system.

SDRAM (Synchronous Dynamic RAM) is so-called because it can keep two sets of memory addresses open simultaneously. By transferring data alter- nately from one set of addresses, and then the other, SDRAM cuts down on the delays associated with non-synchronous RAM, which must close one address bank before opening the next.

The serial port is so called because it transmits the eight bits of a byte of data along one wire, and receives data on another single wire (that is, the data is transmitted in serial form, one bit after another).

SIMM Single In-line Memory Modules are the most common form of RAM. They must be installed in pairs, and do not have the carrying capacity or the speed of DIMMs.

SIMM bank/socket SIMM sockets are the physical slots into which you stick SIMM modules. A pair of SIMM sockets form a SIMM bank, and act as a unit. If only one socket is filled, the bank will not operate.

In Sleep/Suspend mode, all devices except the CPU shut down.

http://www.tyan.com

81

Image 83
Contents InterServe Errata PinsTyan S1832DL Tiger Table of Contents Appendix 1 CPU Retention Module Options Appendix 2 Glossary System ResourcesOverview ChapterIcons Hardware Specifications/Features Disk Drive & System I/O Physical DimensionsBios Information 510 Software SpecificationsTechnical Support Alt.comp.periphs.mainboard.tyanFor Resellers Only Returning Merchandise for ServiceUnpacking InstallationWhat’s the first thing I should do? Install the motherboard into your caseConforms to industry standard revision Plug in the power connector as shownPin Chapter Next are the Com and Printer ports Connecting the USB and PS/2 ports Shows the USB ports and the PS/2 ports Installing your add-in cards is relatively simple butNext, you need to install your memory Install Finally, install your CPU Active Passive Installing CPU Retention ModulesInstalling the Active Processor Chapter Installing the Passive Processor Pin jumpers Or more pin jumpers Off Open Setting JumpersRemoving the CPU You are doneThis page has been intentionally left blank Quick References for Jumpers Onboard Resource SettingsMap of Motherboard Jumpers PS/2 ports COM2 LPT1 COM1 USB ports LM79 PCI slots CPU Settings for 100MHz Bus CPU Settings for 66MHz BusJ10 External Pin Assignments 2x9 External Connector Proprietary Server Mgmt ConnectorHardware Reset Switch Connector Installation Soft Power ConnectorSpeaker Connector Installation Windows 95 Users Chassis Intrusion Alarm ConnectorFlash Eeprom RAM Installation Hardware Cmos & Password ResetDimm Cache MemoryPin Dimm Frequently Asked QuestionsChapter This page has been intentionally left blank Bios Configuration Key Function Main SetupFloppy Drive a and B System Date/TimeType How to Configure Parameter Description Entering Drive ParametersAuto-Detect Hard Disks Boot Sector Virus ProtectionOptimal Defaults Fail-Safe DefaultsAdvanced Cmos Setup Default Settings Chart Advanced Cmos SetupQuick Boot Settings ChartTry Other Boot Devices 1st Boot Device2nd Boot Device 3rd Boot DeviceSystem Bios Cacheable Boot Up Num-LockPassword Check Boot To OS/2C000,16K Shadow and C400,16K Shadow Default Primary VideoCache Bus ECC MPS RevisionAdvanced Chipset Setup Enter Chipset SetupAGP S E R R USB FunctionPort 64/60 Emulation BX Master Latency Timer ClksMulti-Trans Timer Clks USB KB/Mouse Legacy SupportSdram RAS# to CAS# Delay PCI1 to PCI0 AccessDram Integrity Mode Setting Description8bit I/O Recovery Time AGP Multi-Trans Timer AGP ClksAGP Low-Priority Timer Clks AGP Parity Error ResponseTypeF DMA Buffer Control1 16bit I/O Recovery TimeUSB Passive Release PIIX4 Passive ReleasePower Management Setup Enter Power Management SetupAcpi Aware O/S Power Management/APMPower Button Function Green PC Monitor Power StateStandby/Suspend Timer Unit Video Power Down ModeHard Disk Power Down Mode Power Saving TypeLAN Wake-up PC98 Power LEDSlow Clock Ratio Display ActivityRTC Wake-up Plug and Play SetupPlug and Play Setup Default Settings Chart Allocate IRQ to PCI VGA PCI Latency Timer PCI ClocksPlug and Play Aware O/S PCI VGA Palette SnoopDMA Channel n OffBoard PCI IDE Primary IRQOffboard PCI IDE Secondary IRQ PCI Slot n IRQ PriorityPCI Device Search Order Bios Devnode for Shadow RAMReserved Memory Address Peripheral Setup Default Settings Chart Peripheral SetupOverclock Warning Message Default Settings ChartPower Interruption Serial Port2 ModeIR Receiver Pin IR Transmission ModeMode Description Parallel Port ModeOnboardIDE Parallel Port IRQParallel Port DMA Channel Supervisor and User Security Flash Writer Utility Language UtilityBeep Codes System ResourcesIf the computer beeps Then Troubleshooting System ProblemsError Message Explanation Displayed Error MessagesOFF Board Parity Error Addr = Error Message ExplanationAppendix Option Glossary Page Appendix Page Appendix Page Appendix Document # D1308-210