Tyan Computer InterServe 90 manual Reserved Memory Address, PCI Device Search Order

Page 65

Reserved Memory Address

This option specifies the beginning address (in hex) of the reserved memory area. The specified ROM memory area is reserved for use by legacy ISA adapter cards. This option does not appear if the Reserved Memory Size option is set to Disabled. The settings are C0000, C4000, C8000, CC000, D0000, D4000, D8000, or DC000.

PCI Device Search Order

This option changes the BIOS scan order of the PCI slot - from first to last or last to first. The settings are First-Last or Last-First.

BIOS Devnode for Shadow RAM

This option is used for some add-on card ROMs which do not claim the correct memory range that they occupy. The settings are Disabled or Enabled.

BIOS

http://www.tyan.com

63

Image 65

Contents InterServe Errata PinsTyan S1832DL Tiger Table of Contents Appendix 1 CPU Retention Module Options Appendix 2 Glossary System ResourcesOverview ChapterIcons Hardware Specifications/Features Disk Drive & System I/O Physical DimensionsBios Information Technical Support Software SpecificationsAlt.comp.periphs.mainboard.tyan 510For Resellers Only Returning Merchandise for ServiceUnpacking InstallationWhat’s the first thing I should do? Install the motherboard into your caseConforms to industry standard revision Plug in the power connector as shownPin Chapter Next are the Com and Printer ports Connecting the USB and PS/2 ports Shows the USB ports and the PS/2 ports Installing your add-in cards is relatively simple butNext, you need to install your memory Install Finally, install your CPU Active Passive Installing CPU Retention ModulesInstalling the Active Processor Chapter Installing the Passive Processor Removing the CPU Setting JumpersYou are done Pin jumpers Or more pin jumpers Off OpenThis page has been intentionally left blank Quick References for Jumpers Onboard Resource SettingsMap of Motherboard Jumpers PS/2 ports COM2 LPT1 COM1 USB ports LM79 PCI slots CPU Settings for 100MHz Bus CPU Settings for 66MHz BusJ10 External Pin Assignments 2x9 External Connector Proprietary Server Mgmt ConnectorHardware Reset Switch Connector Installation Soft Power ConnectorSpeaker Connector Installation Windows 95 Users Chassis Intrusion Alarm ConnectorFlash Eeprom RAM Installation Hardware Cmos & Password ResetDimm Cache MemoryPin Dimm Frequently Asked QuestionsChapter This page has been intentionally left blank Bios Configuration Key Function Main SetupFloppy Drive a and B System Date/TimeType How to Configure Parameter Description Entering Drive ParametersOptimal Defaults Boot Sector Virus ProtectionFail-Safe Defaults Auto-Detect Hard DisksAdvanced Cmos Setup Default Settings Chart Advanced Cmos SetupQuick Boot Settings Chart2nd Boot Device 1st Boot Device3rd Boot Device Try Other Boot DevicesPassword Check Boot Up Num-LockBoot To OS/2 System Bios CacheableCache Bus ECC Default Primary VideoMPS Revision C000,16K Shadow and C400,16K ShadowAdvanced Chipset Setup Enter Chipset SetupAGP S E R R USB FunctionMulti-Trans Timer Clks BX Master Latency Timer ClksUSB KB/Mouse Legacy Support Port 64/60 EmulationDram Integrity Mode PCI1 to PCI0 AccessSetting Description Sdram RAS# to CAS# DelayAGP Low-Priority Timer Clks AGP Multi-Trans Timer AGP ClksAGP Parity Error Response 8bit I/O Recovery TimeUSB Passive Release 16bit I/O Recovery TimePIIX4 Passive Release TypeF DMA Buffer Control1Power Management Setup Enter Power Management SetupPower Button Function Power Management/APMGreen PC Monitor Power State Acpi Aware O/SHard Disk Power Down Mode Video Power Down ModePower Saving Type Standby/Suspend Timer UnitSlow Clock Ratio PC98 Power LEDDisplay Activity LAN Wake-upRTC Wake-up Plug and Play SetupPlug and Play Setup Default Settings Chart Plug and Play Aware O/S PCI Latency Timer PCI ClocksPCI VGA Palette Snoop Allocate IRQ to PCI VGAOffboard PCI IDE Secondary IRQ OffBoard PCI IDE Primary IRQPCI Slot n IRQ Priority DMA Channel nPCI Device Search Order Bios Devnode for Shadow RAMReserved Memory Address Peripheral Setup Default Settings Chart Peripheral SetupPower Interruption Default Settings ChartSerial Port2 Mode Overclock Warning MessageMode Description IR Transmission ModeParallel Port Mode IR Receiver PinOnboardIDE Parallel Port IRQParallel Port DMA Channel Supervisor and User Security Flash Writer Utility Language UtilityBeep Codes System ResourcesIf the computer beeps Then Troubleshooting System ProblemsError Message Explanation Displayed Error MessagesOFF Board Parity Error Addr = Error Message ExplanationAppendix Option Glossary Page Appendix Page Appendix Page Appendix Document # D1308-210