Tyan Computer InterServe 90 manual Parallel Port IRQ, Parallel Port DMA Channel, OnboardIDE

Page 69

newer devices; consult your device’s user information for the appropriate port type. There are no default settings.

Parallel Port IRQ

This option specifies the IRQ used by the parallel port, and only appears if OnBoard Parallel Port is set to 278 or 378. The settings are 5 or 7.

Parallel Port DMA Channel

This option is only available if the setting for the Parallel Port Mode option is set to ECP and the OnBoard Parallel Port option is set to 378, 278, or 3BC. This option sets the DMA channel used by the parallel port. The settings are 0 through 7 in increments of one.

OnboardIDE

This option specifies the IDE channel used by the onboard IDE controller. The settings are Disabled, Primary, Secondary, or Both.

BIOS

http://www.tyan.com

67

Image 69

Contents InterServe Errata PinsTyan S1832DL Tiger Table of Contents Appendix 1 CPU Retention Module Options Appendix 2 Glossary System ResourcesOverview ChapterIcons Hardware Specifications/Features Physical Dimensions Bios InformationDisk Drive & System I/O Technical Support Software SpecificationsAlt.comp.periphs.mainboard.tyan 510For Resellers Only Returning Merchandise for ServiceUnpacking InstallationWhat’s the first thing I should do? Install the motherboard into your caseConforms to industry standard revision Plug in the power connector as shownPin Chapter Next are the Com and Printer ports Connecting the USB and PS/2 ports Shows the USB ports and the PS/2 ports Installing your add-in cards is relatively simple butNext, you need to install your memory Install Finally, install your CPU Installing CPU Retention Modules Installing the Active ProcessorActive Passive Chapter Installing the Passive Processor Removing the CPU Setting JumpersYou are done Pin jumpers Or more pin jumpers Off OpenThis page has been intentionally left blank Quick References for Jumpers Onboard Resource SettingsMap of Motherboard Jumpers PS/2 ports COM2 LPT1 COM1 USB ports LM79 PCI slots CPU Settings for 100MHz Bus CPU Settings for 66MHz BusJ10 External Pin Assignments 2x9 External Connector Proprietary Server Mgmt ConnectorSoft Power Connector Speaker Connector InstallationHardware Reset Switch Connector Installation Chassis Intrusion Alarm Connector Flash EepromWindows 95 Users RAM Installation Hardware Cmos & Password ResetDimm Cache MemoryPin Dimm Frequently Asked QuestionsChapter This page has been intentionally left blank Bios Configuration Key Function Main SetupFloppy Drive a and B System Date/TimeType How to Configure Parameter Description Entering Drive ParametersOptimal Defaults Boot Sector Virus ProtectionFail-Safe Defaults Auto-Detect Hard DisksAdvanced Cmos Setup Default Settings Chart Advanced Cmos SetupQuick Boot Settings Chart2nd Boot Device 1st Boot Device3rd Boot Device Try Other Boot DevicesPassword Check Boot Up Num-LockBoot To OS/2 System Bios CacheableCache Bus ECC Default Primary VideoMPS Revision C000,16K Shadow and C400,16K ShadowAdvanced Chipset Setup Enter Chipset SetupAGP S E R R USB FunctionMulti-Trans Timer Clks BX Master Latency Timer ClksUSB KB/Mouse Legacy Support Port 64/60 EmulationDram Integrity Mode PCI1 to PCI0 AccessSetting Description Sdram RAS# to CAS# DelayAGP Low-Priority Timer Clks AGP Multi-Trans Timer AGP ClksAGP Parity Error Response 8bit I/O Recovery TimeUSB Passive Release 16bit I/O Recovery TimePIIX4 Passive Release TypeF DMA Buffer Control1Power Management Setup Enter Power Management SetupPower Button Function Power Management/APMGreen PC Monitor Power State Acpi Aware O/SHard Disk Power Down Mode Video Power Down ModePower Saving Type Standby/Suspend Timer UnitSlow Clock Ratio PC98 Power LEDDisplay Activity LAN Wake-upRTC Wake-up Plug and Play SetupPlug and Play Setup Default Settings Chart Plug and Play Aware O/S PCI Latency Timer PCI ClocksPCI VGA Palette Snoop Allocate IRQ to PCI VGAOffboard PCI IDE Secondary IRQ OffBoard PCI IDE Primary IRQPCI Slot n IRQ Priority DMA Channel nBios Devnode for Shadow RAM Reserved Memory AddressPCI Device Search Order Peripheral Setup Default Settings Chart Peripheral SetupPower Interruption Default Settings ChartSerial Port2 Mode Overclock Warning MessageMode Description IR Transmission ModeParallel Port Mode IR Receiver PinParallel Port IRQ Parallel Port DMA ChannelOnboardIDE Supervisor and User Security Flash Writer Utility Language UtilityBeep Codes System ResourcesIf the computer beeps Then Troubleshooting System ProblemsError Message Explanation Displayed Error MessagesOFF Board Parity Error Addr = Error Message ExplanationAppendix Option Glossary Page Appendix Page Appendix Page Appendix Document # D1308-210