Radio Mode Operations
Listening to the radio
1)Press the FUNC button 12 to select radio mode.
2)Press the BND button 13 to select a band. Each time you press the BND button 13 , the band changes in the following order:
FM1 
FM2 
FM3 
AM
* Each time you press the Monaural button | 20 , | |||
the unit toggles between on (stereo) and off | ||||
(monaural). |
| |||
3) Press one of the preset buttons |
| to |
| to |
16 | 21 | |||
Manual memory function
1)Press the BND button 13 to select a band.
2)Slide the Up/Down button 11 to 
(right) or
(left) to tune in to a station.
3)Press and hold for about 2 seconds one of the Preset buttons 16 to 21 where you want to store the station. When a beep sounds, the station is stored in that button.
*One station in each band can be preset to each button.
English
tune in to a station. |
Seek tuning
1) While MANU appears in the display, press |
and hold the BND button 13 for about 1 sec- |
Auto store function
1)Press the BND button 13
2)Press the SHIFT button mode.
*Press the SHIFT button preset mode.
to select a band.
22to select PS/AS
22again to return to
Owner’s Guide
ond to switch to the seek tuning. |
|
2) Slide the Up/Down button 11 to | (right) or |
(left) to start the seek tuning. When a sta- | |
tion is found, it is automatically tuned in.
: Seeks higher frequency stations. 
: Seeks lower frequency stations.
*To stop the seek tuning, slide the Up/Down
button 11 to 
(left) or 
(right).
Manual tuning
1)When MANU does not appear in the display, press and hold the BND button 13 for about 2 seconds to select manual tuning.
*When manual tuning is selected, MANU appears in the display.
2)Slide the Up/Down button 11 to 
(right) or
(left) to tune in to a station.
*Each time you slide the Up/Down button 11 , the frequency changes in 0.2 MHz increments for the FM and in 10 kHz increments for the AM band.
*Press and hold the Up/Down button 11 to 
(right) and 
(left) to increase or decrease the frequency continuously.
3)Press the Auto Store button 17 . Stations with good reception are automatically stored in preset buttons starting from Preset button 16 . (After storing 6 stations, preset No. 1 station is tuned in and auto storing ends.)
*A . S in the display becomes pink.
*Stations with good reception are stored in the order from the current station to stations with a higher frequency. If there are fewer than 6 stations with good reception, the auto storing returns to the lowest frequency and resumes from there.
Note:
•When stations are preset by the auto store function, the station previously stored in the memory at that position is cleared. If there are fewer than 6 stations with good reception, the stations previously stored at the remaining preset buttons are not cleared.
Preset scanning
1)Press the BND button 13 to select a band.
2)Press the SHIFT button 22 to select PS/AS mode.
*Press the SHIFT button 22 to return to preset mode.
Preset memory function
A total of 24 stations can be preset, 6 each for
the FM1, FM2, FM3, and AM bands.
Note:
•When a station is preset, the station previously stored in the memory at that position is cleared.
3)When the Preset Scan button 16 is pressed, the preset stations are tuned in for 5 seconds each from Preset button 16 .
*P. S in the display becomes pink.
*When a preset station has been tuned in, preset scanning starts from the station after the current one. When a preset station has not been tuned in, preset scanning starts from preset No. 1.
17