NETGEAR DGN2200V3 user manual N300 Wireless ADSL2+ Modem Router DGN2200v3 Front Panel LEDs

Page 10

N300 Wireless ADSL2+ Modem Router DGN2200v3

Table 1. Front Panel LEDs

Icon

LED Activity

Description

 

 

 

Power

Solid green

Power is supplied to the modem router.

 

 

 

 

Solid red

POST (power-on self-test) failure or a device malfunction has occurred.

 

 

 

 

Off

Power is not supplied to the modem router.

 

 

 

 

Restore factory

The LED blinks momentarily when the Restore Factory Settings button on

 

settings

the bottom of the unit is pressed for 6 seconds (pressing it briefly resets the

 

 

unit). The Power LED then blinks red three times when the Restore Factory

 

 

Settings button is released and then turns green as the gateway resets to

 

 

the factory defaults.

 

 

 

LAN

Solid green

The LAN port has detected an Ethernet link with a device.

 

 

 

 

Blinking green

Data is being transmitted or received.

 

 

 

 

Off

No link is detected on this port.

 

 

 

USB

Off

• No USB device connected.

 

 

• “Safely Remove Hardware” has been activated.

 

 

• An error has occurred with the device.

 

 

 

 

Solid green

USB device is ready to use.

 

 

 

 

Blinking green

USB device is in use.

 

 

 

DSL

Solid green

You have a DSL connection. In technical terms, the DSL port is

 

 

synchronized with an ISP’s network-access device.

 

 

 

 

Blinking green

Indicates that the modem router is negotiating the best possible speed on

 

 

the DSL line.

 

 

 

 

Off

The unit is off or there is no DSL link established.

 

 

 

Internet

Solid green

You have an Internet connection. If this connection is dropped due to an

 

 

idle time-out but the DSL connection is still present, the light stays green. If

 

 

the Internet connection is dropped for any other reason, the light turns off.

 

 

 

 

Solid red

The Internet (IP) connection failed. See Troubleshooting the Internet

 

 

Connection on page 103 for troubleshooting information.

 

 

 

 

Blinking green

Data is being transmitted over the DSL port.

 

 

 

Wireless

Off

No Internet connection is detected or the device is in bridge mode (an

 

 

external device handles the ISP connection).

 

 

 

 

Solid green

There is wireless connectivity.

Icon is on the

 

 

Blinking green

Data is being transmitted or received over the wireless link.

Wireless

 

 

button

Off

There is no wireless connectivity. You can still plug an Ethernet cable into

 

 

 

one of the LAN ports to get wired connectivity. See Turn Off Wireless

 

 

Connectivity on page 30 for more information about the use of this button.

 

 

 

Hardware Setup

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents N300 Wireless ADSL2+ Modem Router DGN2200v3 Trademarks Technical SupportStatement of Conditions Contents Security Settings USB Storage Appendix a Supplemental Information Hardware Setup Unpack Your Modem Router Hardware FeaturesLabel Back Panel Front PanelN300 Wireless ADSL2+ Modem Router DGN2200v3 Front Panel LEDs Modem Router Stand WPSPosition Your Modem Router Adsl MicrofiltersTwo-Line Adsl Microfilter One-Line Adsl MicrofilterSummary Cable Your Modem Router  To cable the modem routerAdd power to the modem router Verify the Cabling Modem Router Setup Replace an Existing Modem and Router Modem Router Setup PreparationUse Standard TCP/IP Properties for Dhcp Gather ISP InformationView or Change Settings Netgear Genie SetupSettings Description Log In to the Modem Router  To log To upgrade the firmware Upgrade Modem Router FirmwareModem Router Interface Setup Wizard  To use the Setup WizardManual Setup Basic Settings ISP does not require login ISP does require login Does Your ISP Require a Login? Answer either yes or noWhen a login is required, these fields display Internet IP AddressAdsl Settings  To manually specify the Adsl settings To change the password and login time-out Change Password and Login Time-OutUnsuccessful Internet Connection Types of Logins Log Out ManuallyWireless Settings Wireless Adapter CompatibilityTurn Off Wireless Connectivity Preset SecuritySecurity Basics Wireless Security Options Disable Ssid BroadcastRestrict Access by MAC Address Add Clients Computers or Devices to Your Network To join the wireless network using a WPS button Wi-Fi Protected Setup WPS Method To join the wireless network Manual MethodWireless Settings Screen  To view or change wireless settings View or Change Wireless SettingsConsider Every Device on Your Network Wireless Network Wireless Settings Screen FieldsSecurity Options Settings  To set up WEP security  To change the WPA Security Option and passphraseWireless Guest Networks N300 Wireless ADSL2+ Modem Router DGN2200v3 Security Settings Logs Examples of Log Messages Activation and AdministrationDropped Packets  To delete a keyword or domain  To block sites using keywords Select Security Block SitesKeyword Blocking of Http Traffic  To specify a trusted computerSet Up Firewall Rules Firewall Rules to Control Network Access To set up firewall rules Port Triggering to Open Incoming Ports Port Forwarding to Permit External Host Communications Set Up Port Forwarding to Local Servers How Port Forwarding Differs from Port TriggeringAdd a Custom Service Application Example Make a Local Web Server Public Click Edit Service or Delete ServiceEdit or Delete a Port Forwarding Entry  To edit or delete a port forwarding entrySet Up Port Triggering  To enable port triggeringClear the Disable Port Triggering check box  To add a port triggering serviceN300 Wireless ADSL2+ Modem Router DGN2200v3 Set the Time Zone  To set the time zone Select Security ScheduleSchedule Services  To schedule services Select Security ScheduleEnable Security Event Email Notification N300 Wireless ADSL2+ Modem Router DGN2200v3 Network Maintenance Upgrade the Modem Router Firmware Automatic Firmware CheckManually Check for Firmware Upgrades  To stop automatic firmware checkingBack Up and Manage the Configuration File  To back up the modem router configuration file To erase the configuration  To restore the configuration fileView Router Status LAN Port Local Ports Internet Port SettingsWireless Port ModemPort Show StatisticsAdsl Link Downstream or Upstream View Attached Devices Authentication. On or OffConnection Status Run Diagnostic Utilities Select Maintenance Attached DevicesUSB Storage ReadySHARE Access USB Drive RequirementsStoring Files in a Central Location for Printing File-Sharing ScenariosSharing Photos  To share files with your friends and familyUSB Storage Basic Settings Sharing Large Files over the InternetN300 Wireless ADSL2+ Modem Router DGN2200v3 Edit a Network Folder  To edit a network folderUSB Storage Advanced Settings Access MethodAvailable Network Folders Create a Network Folder To create a network folder Media Server Settings Safely Remove USB DriveApproved USB Devices Advanced USB Settings Select the Allow only approved devices check boxConnect to the USB Drive from a Remote Computer Connect to the USB Drive with Microsoft Network SettingsSelect Maintenance Router Status Enabling File and Printer SharingConfiguring Windows 98SE and Windows ME Configuring Windows 2000 and Windows XPAdvanced Settings WAN Setup Default DMZ Server  To assign a computer or server to be a default DMZ serverSelect the Use a Dynamic DNS Service check box  To set up Dynamic DNSDynamic DNS  To change the LAN settings Select Advanced LAN Setup LAN SetupLAN IP address IP Address Reservation LAN Setup Screen Settings To reserve an IP address  To edit or delete a reserved address entry Quality of Service QoS To set up QoS Select Advanced QoS Setup Click Edit or DeleteN300 Wireless ADSL2+ Modem Router DGN2200v3 Advanced Wireless Settings Advanced Wireless Settings To view or change advanced wireless settings Wireless Card Access List WPS Settings To set up a wireless card access list Remote Management Static Routes Static Route Example To add a static route Universal Plug and Play  To set up UPnP Traffic Meter Wireless Bridging and Repeating Networks N300 Wireless ADSL2+ Modem Router DGN2200v3 Set Up a Point-to-Point Bridge  To set up a point-to-point bridge configurationSet Up a Multi-Point Bridge  To set up the multi-point bridge configurationRepeater with Wireless Client Association  To set up a repeater with wireless client association Repeater exampleChange the Device Mode  To change the device modeTroubleshooting Power LED Is Off Troubleshooting with the LEDsPower LED Is Red Cannot Log In to the Wireless-N Modem Router LAN LED Is OffAdsl Link LED Is Green Troubleshooting the Internet ConnectionAdsl Link Adsl Link LED Is Blinking GreenInternet LED Is Red Troubleshooting PPPoE or PPPoAObtaining an Internet IP Address TCP/IP Network Not Responding Troubleshooting Internet BrowsingTest the LAN Path to Your Modem Router Test the Path from Your Computer to a Remote Device PingChanges Not Saved Incorrect Date or TimeSupplemental Information Factory Settings Factory Default SettingsBest Specifications Specification DescriptionNotification of Compliance 113 FCC Requirements for Operation in the United States FCC Information to UserImportant Note Radiation Exposure Statement Industry CanadaGPL License Agreement Interference Reduction Table Index 118 119 120
Related manuals
Manual 2 pages 44.57 Kb

DGN2200V3, N300 specifications

The NETGEAR N300 is a high-performance wireless router designed for home and small office use, offering impressive speeds and connectivity for various online activities. With a maximum wireless speed of up to 300 Mbps, it caters efficiently to activities such as streaming HD video, online gaming, and browsing the web. This makes the N300 a versatile choice for users with demanding bandwidth needs.

One of the standout features of the NETGEAR N300 is its compatibility with a range of devices, including laptops, smartphones, tablets, and gaming consoles. The router supports both wired and wireless connections, ensuring that users can connect a variety of gadgets using Ethernet cables or through 802.11n Wi-Fi technology. This dual-band capability enhances flexibility, allowing users to choose the best connection type based on their needs.

The N300 incorporates advanced technologies to optimize performance. Equipped with SpeedBoost technology, it delivers improved range and reliability by adjusting the wireless signal strength. This ensures a stable connection throughout larger homes or office spaces, reducing interruptions and enhancing user experience. The router also features QoS (Quality of Service), which prioritizes bandwidth for high-demand applications, ensuring that streaming and gaming receive the necessary resources for a seamless experience.

Security is a significant concern for many users, and the NETGEAR N300 addresses this with robust security features. It employs WPA/WPA2 encryption for safe wireless communication, protecting sensitive data from potential intruders. Additionally, the router includes a built-in firewall, providing an extra layer of defense against external threats.

Installation and setup are straightforward, thanks to the intuitive web interface and support for multiple languages. Users can quickly configure their network settings, manage connected devices, and monitor performance through a user-friendly dashboard. Additionally, the N300 is equipped with a USB port that enables file sharing and media streaming across the network.

Overall, the NETGEAR N300 is an excellent choice for anyone looking to enhance their home or small office network with reliable performance, strong security, and flexibility. Its combination of speed, range, and user-friendly features makes it a standout option in the wireless router market, catering to the needs of diverse users.
Top Page Image Contents