NETGEAR DGN2200V3, N300 user manual Manual Setup Basic Settings

Page 23

N300 Wireless ADSL2+ Modem Router DGN2200v3

3.If you selected Yes, click Next.

With automatic Internet detection, the Setup Wizard searches your Internet connection for servers and protocols to determine your ISP configuration.

Note: The Setup Wizard cannot detect a Point-to-Point Tunneling Protocol (PPTP) connection. If your ISP uses PPTP, you have to set your Internet connection through the screen described in Manual Setup

(Basic Settings) on page 23.

Manual Setup (Basic Settings)

The Basic Settings screen displays when you select No. I want to configure the Router myself in the Setup Wizard and is also available from the modem router menu. It is where you view or change ISP information. The fields that display vary depending on whether or not your Internet connection requires a login.

To use Basic Settings to specify your Internet settings manually:

Note: Check that the country is set as described Setup Wizard on page 22 before proceeding with the manual setup.

1.Select Set Up > Basic Settings, and select Yes or No depending on whether or not your ISP requires a login. Figure , The following descriptions explain all of the possible fields in the Basic Settings screen. Note that which fields appear in this screen depends on whether or not an ISP login is required. shows both forms of the Basic Settings screen.

•Yes. Select the encapsulation method and enter the login name. If you want to change the login time-out, enter a new value in minutes.

•No. Enter the account and domain names, as needed.

2.Enter the settings for the IP address and DNS server. The default DSL settings usually work fine. If you have problems with your connection, check the DSL settings, and see ADSL Settings on page 26 for more information.

3.If no login is required, you can specify the MAC Address setting.

4.Click Apply to save your settings.

Modem Router Setup

23

Image 23

Contents N300 Wireless ADSL2+ Modem Router DGN2200v3 Statement of Conditions Technical SupportTrademarks Contents Security Settings USB Storage Appendix a Supplemental Information Hardware Setup Label Hardware FeaturesUnpack Your Modem Router Front Panel Back PanelN300 Wireless ADSL2+ Modem Router DGN2200v3 Front Panel LEDs WPS Modem Router StandAdsl Microfilters Position Your Modem RouterSummary One-Line Adsl MicrofilterTwo-Line Adsl Microfilter  To cable the modem router Cable Your Modem RouterAdd power to the modem router Verify the Cabling Modem Router Setup Gather ISP Information Modem Router Setup PreparationUse Standard TCP/IP Properties for Dhcp Replace an Existing Modem and RouterSettings Description Netgear Genie SetupView or Change Settings  To log Log In to the Modem RouterModem Router Interface Upgrade Modem Router Firmware To upgrade the firmware  To use the Setup Wizard Setup WizardManual Setup Basic Settings Does Your ISP Require a Login? Answer either yes or no ISP does not require login ISP does require loginInternet IP Address When a login is required, these fields display To manually specify the Adsl settings Adsl SettingsUnsuccessful Internet Connection Change Password and Login Time-Out To change the password and login time-out Log Out Manually Types of LoginsWireless Adapter Compatibility Wireless SettingsSecurity Basics Preset SecurityTurn Off Wireless Connectivity Add Clients Computers or Devices to Your Network Disable Ssid BroadcastRestrict Access by MAC Address Wireless Security OptionsManual Method Wi-Fi Protected Setup WPS Method To join the wireless network  To join the wireless network using a WPS buttonWireless Settings Screen Consider Every Device on Your Network View or Change Wireless Settings To view or change wireless settings Security Options Settings Wireless Settings Screen FieldsWireless Network  To change the WPA Security Option and passphrase  To set up WEP securityWireless Guest Networks N300 Wireless ADSL2+ Modem Router DGN2200v3 Security Settings Logs Dropped Packets Activation and AdministrationExamples of Log Messages  To specify a trusted computer  To block sites using keywords Select Security Block SitesKeyword Blocking of Http Traffic  To delete a keyword or domain To set up firewall rules Firewall Rules to Control Network AccessSet Up Firewall Rules Port Triggering to Open Incoming Ports Port Forwarding to Permit External Host Communications How Port Forwarding Differs from Port Triggering Set Up Port Forwarding to Local ServersAdd a Custom Service  To edit or delete a port forwarding entry Click Edit Service or Delete ServiceEdit or Delete a Port Forwarding Entry Application Example Make a Local Web Server Public To enable port triggering Set Up Port Triggering To add a port triggering service Clear the Disable Port Triggering check boxN300 Wireless ADSL2+ Modem Router DGN2200v3  To set the time zone Select Security Schedule Set the Time Zone To schedule services Select Security Schedule Schedule ServicesEnable Security Event Email Notification N300 Wireless ADSL2+ Modem Router DGN2200v3 Network Maintenance Automatic Firmware Check Upgrade the Modem Router Firmware To stop automatic firmware checking Manually Check for Firmware Upgrades To back up the modem router configuration file Back Up and Manage the Configuration FileView Router Status  To restore the configuration file To erase the configuration Modem Internet Port SettingsWireless Port LAN Port Local PortsAdsl Link Downstream or Upstream Show StatisticsPort Connection Status Authentication. On or OffView Attached Devices Select Maintenance Attached Devices Run Diagnostic UtilitiesUSB Storage USB Drive Requirements ReadySHARE Access To share files with your friends and family File-Sharing ScenariosSharing Photos Storing Files in a Central Location for PrintingSharing Large Files over the Internet USB Storage Basic SettingsN300 Wireless ADSL2+ Modem Router DGN2200v3  To edit a network folder Edit a Network FolderAccess Method USB Storage Advanced Settings To create a network folder Create a Network FolderAvailable Network Folders Safely Remove USB Drive Media Server SettingsSelect the Allow only approved devices check box Approved USB Devices Advanced USB SettingsEnabling File and Printer Sharing Connect to the USB Drive with Microsoft Network SettingsSelect Maintenance Router Status Connect to the USB Drive from a Remote ComputerConfiguring Windows 2000 and Windows XP Configuring Windows 98SE and Windows MEAdvanced Settings WAN Setup  To assign a computer or server to be a default DMZ server Default DMZ ServerDynamic DNS  To set up Dynamic DNSSelect the Use a Dynamic DNS Service check box LAN IP address LAN Setup To change the LAN settings Select Advanced LAN Setup  To reserve an IP address LAN Setup Screen SettingsIP Address Reservation Click Edit or Delete Quality of Service QoS To set up QoS Select Advanced QoS Setup  To edit or delete a reserved address entryN300 Wireless ADSL2+ Modem Router DGN2200v3  To view or change advanced wireless settings Advanced Wireless SettingsAdvanced Wireless Settings  To set up a wireless card access list WPS SettingsWireless Card Access List Remote Management Static Route Example Static Routes To add a static route Universal Plug and Play  To set up UPnP Traffic Meter Wireless Bridging and Repeating Networks N300 Wireless ADSL2+ Modem Router DGN2200v3  To set up a point-to-point bridge configuration Set Up a Point-to-Point Bridge To set up the multi-point bridge configuration Set Up a Multi-Point BridgeRepeater with Wireless Client Association Repeater example  To set up a repeater with wireless client association To change the device mode Change the Device ModeTroubleshooting Power LED Is Red Troubleshooting with the LEDsPower LED Is Off LAN LED Is Off Cannot Log In to the Wireless-N Modem RouterAdsl Link LED Is Blinking Green Troubleshooting the Internet ConnectionAdsl Link Adsl Link LED Is GreenObtaining an Internet IP Address Troubleshooting PPPoE or PPPoAInternet LED Is Red Test the LAN Path to Your Modem Router Troubleshooting Internet BrowsingTCP/IP Network Not Responding Ping Test the Path from Your Computer to a Remote DeviceIncorrect Date or Time Changes Not SavedSupplemental Information Factory Default Settings Factory SettingsBest Specification Description SpecificationsNotification of Compliance 113 FCC Information to User FCC Requirements for Operation in the United StatesGPL License Agreement Industry CanadaImportant Note Radiation Exposure Statement Interference Reduction Table Index 118 119 120

Related manuals

Manual 2 pages 44.57 Kb