NETGEAR N300, DGN2200V3 user manual Show Statistics, Port, Adsl Link Downstream or Upstream

Page 62

N300 Wireless ADSL2+ Modem Router DGN2200v3

Channel. The current channel, which determines the operating frequency. Mode. The current mbps setting.

Wireless AP. Indicates if the access point feature is enabled. If disabled, the Wireless LED on the front panel is off.

Broadcast Name. Indicates if the modem router is configured to broadcast its SSID.

Show Statistics

Click the Show Statistics button on the Router Status screen to display a screen similar to this:

Port

The statistics for the WAN (Internet), LAN (local), and wireless LAN (WLAN) ports. For each port, the screen displays the following:

•Status. The link status of the port.

•TxPkts. The number of packets transmitted since reset or manual clear.

•RxPkts. The number of packets received since reset or manual clear.

•Collisions. The number of collisions since reset or manual clear.

•Tx B/s. The current line utilization—percentage of current bandwidth used.

•Rx B/s. The average line utilization.

•Up Time. The time elapsed since the last power cycle or reset.

ADSL Link Downstream or Upstream

The statistics for the upstream and downstream DSL link. These statistics are of interest to your technical support representative if you have problems obtaining or maintaining a connection.

Network Maintenance

62

Image 62

Contents N300 Wireless ADSL2+ Modem Router DGN2200v3 Statement of Conditions Technical SupportTrademarks Contents Security Settings USB Storage Appendix a Supplemental Information Hardware Setup Label Hardware FeaturesUnpack Your Modem Router Back Panel Front PanelN300 Wireless ADSL2+ Modem Router DGN2200v3 Front Panel LEDs Modem Router Stand WPSPosition Your Modem Router Adsl MicrofiltersSummary One-Line Adsl MicrofilterTwo-Line Adsl Microfilter Cable Your Modem Router  To cable the modem routerAdd power to the modem router Verify the Cabling Modem Router Setup Replace an Existing Modem and Router Modem Router Setup PreparationUse Standard TCP/IP Properties for Dhcp Gather ISP InformationSettings Description Netgear Genie SetupView or Change Settings Log In to the Modem Router  To logModem Router Interface Upgrade Modem Router Firmware To upgrade the firmware Setup Wizard  To use the Setup WizardManual Setup Basic Settings ISP does not require login ISP does require login Does Your ISP Require a Login? Answer either yes or noWhen a login is required, these fields display Internet IP AddressAdsl Settings  To manually specify the Adsl settingsUnsuccessful Internet Connection Change Password and Login Time-Out To change the password and login time-out Types of Logins Log Out ManuallyWireless Settings Wireless Adapter CompatibilitySecurity Basics Preset SecurityTurn Off Wireless Connectivity Wireless Security Options Disable Ssid BroadcastRestrict Access by MAC Address Add Clients Computers or Devices to Your Network To join the wireless network using a WPS button Wi-Fi Protected Setup WPS Method To join the wireless network Manual MethodWireless Settings Screen Consider Every Device on Your Network View or Change Wireless Settings To view or change wireless settings Security Options Settings Wireless Settings Screen FieldsWireless Network  To set up WEP security  To change the WPA Security Option and passphraseWireless Guest Networks N300 Wireless ADSL2+ Modem Router DGN2200v3 Security Settings Logs Dropped Packets Activation and AdministrationExamples of Log Messages  To delete a keyword or domain  To block sites using keywords Select Security Block SitesKeyword Blocking of Http Traffic  To specify a trusted computer To set up firewall rules Firewall Rules to Control Network AccessSet Up Firewall Rules Port Triggering to Open Incoming Ports Port Forwarding to Permit External Host Communications Set Up Port Forwarding to Local Servers How Port Forwarding Differs from Port TriggeringAdd a Custom Service Application Example Make a Local Web Server Public Click Edit Service or Delete ServiceEdit or Delete a Port Forwarding Entry  To edit or delete a port forwarding entrySet Up Port Triggering  To enable port triggeringClear the Disable Port Triggering check box  To add a port triggering serviceN300 Wireless ADSL2+ Modem Router DGN2200v3 Set the Time Zone  To set the time zone Select Security ScheduleSchedule Services  To schedule services Select Security ScheduleEnable Security Event Email Notification N300 Wireless ADSL2+ Modem Router DGN2200v3 Network Maintenance Upgrade the Modem Router Firmware Automatic Firmware CheckManually Check for Firmware Upgrades  To stop automatic firmware checking Back Up and Manage the Configuration File  To back up the modem router configuration fileView Router Status  To restore the configuration file To erase the configuration LAN Port Local Ports Internet Port SettingsWireless Port ModemAdsl Link Downstream or Upstream Show StatisticsPort Connection Status Authentication. On or OffView Attached Devices Run Diagnostic Utilities Select Maintenance Attached DevicesUSB Storage ReadySHARE Access USB Drive RequirementsStoring Files in a Central Location for Printing File-Sharing ScenariosSharing Photos  To share files with your friends and familyUSB Storage Basic Settings Sharing Large Files over the InternetN300 Wireless ADSL2+ Modem Router DGN2200v3 Edit a Network Folder  To edit a network folderUSB Storage Advanced Settings Access Method To create a network folder Create a Network FolderAvailable Network Folders Media Server Settings Safely Remove USB DriveApproved USB Devices Advanced USB Settings Select the Allow only approved devices check boxConnect to the USB Drive from a Remote Computer Connect to the USB Drive with Microsoft Network SettingsSelect Maintenance Router Status Enabling File and Printer SharingConfiguring Windows 98SE and Windows ME Configuring Windows 2000 and Windows XPAdvanced Settings WAN Setup Default DMZ Server  To assign a computer or server to be a default DMZ serverDynamic DNS  To set up Dynamic DNSSelect the Use a Dynamic DNS Service check box LAN IP address LAN Setup To change the LAN settings Select Advanced LAN Setup  To reserve an IP address LAN Setup Screen SettingsIP Address Reservation  To edit or delete a reserved address entry Quality of Service QoS To set up QoS Select Advanced QoS Setup Click Edit or DeleteN300 Wireless ADSL2+ Modem Router DGN2200v3  To view or change advanced wireless settings Advanced Wireless SettingsAdvanced Wireless Settings  To set up a wireless card access list WPS SettingsWireless Card Access List Remote Management Static Routes Static Route Example To add a static route Universal Plug and Play  To set up UPnP Traffic Meter Wireless Bridging and Repeating Networks N300 Wireless ADSL2+ Modem Router DGN2200v3 Set Up a Point-to-Point Bridge  To set up a point-to-point bridge configurationSet Up a Multi-Point Bridge  To set up the multi-point bridge configurationRepeater with Wireless Client Association  To set up a repeater with wireless client association Repeater exampleChange the Device Mode  To change the device modeTroubleshooting Power LED Is Red Troubleshooting with the LEDsPower LED Is Off Cannot Log In to the Wireless-N Modem Router LAN LED Is OffAdsl Link LED Is Green Troubleshooting the Internet ConnectionAdsl Link Adsl Link LED Is Blinking GreenObtaining an Internet IP Address Troubleshooting PPPoE or PPPoAInternet LED Is Red Test the LAN Path to Your Modem Router Troubleshooting Internet BrowsingTCP/IP Network Not Responding Test the Path from Your Computer to a Remote Device PingChanges Not Saved Incorrect Date or TimeSupplemental Information Factory Settings Factory Default SettingsBest Specifications Specification DescriptionNotification of Compliance 113 FCC Requirements for Operation in the United States FCC Information to UserGPL License Agreement Industry CanadaImportant Note Radiation Exposure Statement Interference Reduction Table Index 118 119 120

Related manuals

Manual 2 pages 44.57 Kb