NETGEAR PS111W manual Appendix E IP Setup, IP Configuration Settings, Setting Recommended Value

Page 103

NetGear Print Server Manual

Appendix E IP Setup

This appendix provides a brief overview of IP addressing.

Overview

This appendix is intended only when the user has inadvertently disabled the DHCP protocol and/or assigned a wrong subnet IP address. Refer to See IP Configuration Settings to assign a static IP address.

The following table describes each setting.

IP Configuration Settings


Setting	Recommended Value

Device Name	Shown on a sticker on the base of the device in the form "PSxxxxxx."

Device IP Address	192.168.0.1

Gateway IP Address	0.0.0.0

Subnet Mask	0.0.0.0.
Subnet Mask

Clicking on Reset will set all values back to zero, and clicking on OK sets the data entered. Ensure that the IP address assigned to the device is not already in use.

Following picture is the NETGEAR Print Server IP Address Configuration window.

NETGEAR Print Server IP Address Configuration

94

Image 103

Contents Installation and Reference For Netgear PS111W Print Sever 2000, 2002 by NETGEAR, Inc. All rights reserved Bestätigung des Herstellers/Importeurs United States 888-NETGEAR Purpose PrefaceAudience Use of Enter, Type, and Press ConventionsRelated Publication Special Message FormatsChapter List of FTP Files and Commands Supported by the Print Server Appendix C Config File Introduction FeaturesFront Panel of the Model PS111W Print Sever Front PanelColor Activity Description LEDsLED Descriptions Label2Rear Panel of the Model PS111W Print Sever Rear PanelVerifying Package Contents InstallationPreparing the Site Connecting Devices to the Print Server Verifying Power Connecting to the Print Server Configuring Print Server for TCP/IPWeb Management for Print Server Server Status Browser Menu selections and Configuration ScreensSystem Configuration Screen Configure ServerPrint Server Name Password Confirm Password Enable Protocols Configure Server FieldsTCP/IP TCP/IP Configuration FieldsAppleTalk Apple Talk Configuration FieldsChannel No WirelessConfiguration fields and buttons Regulatory Domain Station NameNetwork Type WEP Data Privacy Fields Current Channel Current Tx Rate Throughput Wireless Link InfoWireless Link Info Fields Stat AssociatedPrinter Port Printer PortLogical Port Fields Logical PrinterButtons Reset Printing in Windows Microsoft Windows System PrintingPrint Server Installation Netgear Print Server Software InstallationInformation Components Destination Location Page There will be a program group created and shown as below Page Netgear Print Server software Icon Setting Up Your PC to Recognize the Print ServerNetGear Print Server Manual To set up each PC Click on Next Select the PS111W print server and click on Next Auto-IP 13 Set up TCP/IP for Print Server to get an IP address Wireless Configuration 14 Wireless Configuration Click on Finish Click on OK Netgear Add Printer Wizard Write Down the Port NameAddport Window Epson Connection 19 Epson Spool Manager Queue Setup WindowWrite Down the Port Name ADD Port WindowSelect Printer Port for Add Printer Wizard Add a printer to your system to print22 Find and select the printer port 23 Add Printer Wizard 24 Use Existing Driver for Add Printer Wizard 25 Name Your Printer for Add Printer Wizard 26 Share Printer for Add Printer Wizard If you answer Yes to print a test page, see Figure 29 Completing the Add Printer Wizard Unix Printing Using TCP/IP Assigning an IP Address to the Print Server Using Dhcp Temporary IP Address ResolutionAssigning an IP Address to the Print Server Using BootP Assigning an IP Address to the Print Server Using Rarp Assigning an IP Address to the Print Server Using ARP Arp -s Name 00c002xxyyzz Configuration Example Configuring Your Print Server Using FTPFile Name Purpose Mode FTP CommandsFTP Files in the Directory LPD Configuration and Printing Setting the Print MethodAction Sample Command Sample Commands for Using LPD on SystemAction Sample Commands for Using LPD on BSDSocket Number Definitions Printing Using LPDPrinting Using FTP Printing Using DSIAppleTalk Printing Setting up Print Server for AppleTalkSetting up Host Computer Sample CONFIG.3P Configuration File Using PSTool UtilityPSTool Utility Config File Entries PSTool Utility Config File FormatEntry inConfig File Description Using Advanced Management Tools Advanced Button ButtonsBrowse Button System Tab Advanced Print Server ConfigurationField Description System Tab Fields TCP/IP Tab Window TCP/IP TabAppleTalk Tab AppleTalk TabLogical Port Tab Window Logical Port TabPhysical Port Tab Physical Port Wireless TabSsid Use the same Channel number Link Info Screen Wireless Link InfoControl Menu Menu OptionsPrinter Menu Help Menu Configuring Using IP SetupGeneral Specifications Appendix a Technical SpecificationsEN 55 022 Cispr 22, Class B Vcci Class B ITE IP Addresses and the Internet Appendix B Understanding IP AddressesThree Main Address Classes Netmask Number of Bits Dotted-Decimal Value Subnet AddressingExample of Subnetting a Class B Address Netmask Notation Translation Table for One OctetNetmask Formats Private IP AddressesDotted-Decimal Masklength IP Configuration by Dhcp Address Resolution ProtocolParameter and Command Appendix C Config FileConfig File TCP/IP Settings Configuration SettingsLogical Printer Line Numbers Config File Line NumbersCreate Ndps Manager Object Window Appendix D Using NetWare 5 NdpsOverview Creating an Ndps Manager ObjectCreate Printer Agent Window Creating an Ndps Printer AgentConfigure Port Handler Window Workstation ConfigurationClick on Close IP Configuration Settings Appendix E IP SetupSetting Recommended Value Hexadecimal Value Ascii Character Appendix F Ascii to Hexadecimal Conversion TableNetGear Print Server Manual NetGear Print Server Manual

Related manuals

Manual 21 pages 56.15 Kb