NetComm NB504 manual Quick Setup Wireless settings

Page 17

After you complete the above, click Next, the Wireless settings page will appear, shown in figure 4-9.

Figure 4-9 Quick Setup - Wireless settings

In this page, you can configure the following wireless parameters:

Wireless Radio - Indicates whether the Access Point feature of the router is enabled or disabled. If disabled, the WLAN LED on the front panel will not be lit and the wireless stations will not be able to access the router. If enabled, the WLAN LED will be lit up and wireless stations will be able to access the router.

SSID - Enter a value of up to 32 characters. The same SSID must be assigned to all wireless devices on your network. The default SSID is Wireless. This value is case-sensitive. For example, Netcomm is NOT the same as Netcomm.

Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the router can be used. It may be illegal to use the wireless function of the router in a region other than one of those specified in this field.

Channel - The current channel in use. This field determines which operating frequency will be used.

Mode - Indicates the current mode 54Mbps (802.11g), 11Mbps (802.11b). If you select 54Mbps (802.11g), it is compatible with 11Mbps (802.11b).

These settings are only for basic wireless parameters, for advanced settings, please refer to Section 5.5: “Wireless.”

Note: The change of wireless settings won’t take effect until the routerreboots! You can reboot it manually. If you need instructions as

to how to do this, please referto Section 5.11.5: “Rebooting the Router

YML864 Rev1

����NB504 ��User�� Guid����e

www.netcomm.com.au

17

Image 17
Contents User Guide Contents Virtual Servers Package contents Purposes About this GuideConventions Overview of this User GuideOverview of the Router IntroductionFeatures Front Panel Panel LayoutRear Panel System Requirements Connecting the RouterInstallation Environment Requirements Power off your PC, Cable/DSL modem, and the router Connecting the RouterTCP/IP configuration Quick Installation GuideSuccessful result of Ping command Login the router Quick Installation GuideQuick Setup Quick Setup Static IP Quick Setup Wireless settings Setup Login Configuring the RouterWAN StatusRouter Status 1 LAN Quick SetupNetwork 2 WAN You can configure the WAN port parameters on thisWAN Static IP WAN PPPoE Click the Save button to save your settings 802.1X + Dynamic IP Settings 802.1X + Static IP Settings 10 BigPond Settings 11 L2TP Settings 12 Pptp Settings NB504 User Guide 13 MAC Address Clone MAC Clone14 Wireless menu Wireless15 Wireless Settings Wireless SettingsMode Select the desired wireless mode. The options are 15a WPA-PSK/WPA2-PSK MAC Filtering 16 Wireless MAC address FilteringModify the information Click the Save button NB504 User Guide 18 The router attached wireless stations Wireless Statistics19 The Dhcp menu Dhcp20 Dhcp Settings Dhcp Settings21 Dhcp Clients List Dhcp Clients List22 Address Reservation Address ReservationClick the Save button when finished Virtual Servers Forwarding26 Add or Modify a Virtual Server Entry 27 Port Triggering Port Triggering28 Add or Modify a Triggering Entry 29 DMZ 3 DMZUPnP 30 UPnP Settings31 The Security menu SecurityFirewall 32 Firewall Settings33 IP address Filtering IP Address FilteringModify the information Click the Save button 35 Domain Filtering Domain FilteringNB504 User Guide 37 MAC address Filtering NB504 User Guide 39 Remote Management Remote ManagementAdvanced Security 40 Advanced Security settings41 Thwarted DoS Host Table Binding Setting IP & MAC Binding Setting45 Find IP & MAC Binding Entry 46ARP List ARP List47 Static Routing Static Routing11.1Dyndns.org Ddns Dynamic DdnsOray.net Ddns 50 Oray.net Ddns SettingsComexe.cn Ddns 51 Comexe.cn Ddns Settings52 The System Tools menu System ToolsTime 53 Time settingsFirmware 54 Firmware UpgradeBackup and Restore Factory Defaults57 Reboot the router Reboot59 System Log 12.7 Log60 Statistics StatisticsFigure A-1 PPPoE Connection Type Appendix a FAQFigure A-3 MAC Clone Want to build a WEB Server on the LAN, what should I do? Want to use Netmeeting, what do I need to do?Figure A-7 Remote Management Wireless stations cannot connect to the router Figure B-1 Add Network Protocol Appendix B Configuring the PCFigure B-3 Configuration tab Configure TCP/IP for your computerFigure B-5 Gateway tab Figure B-7 IP Address tab Figure B-9 DNS Configuration tab General Appendix C SpecificationsAppendix D Glossary Customer Information Appendix E Legal & Regulatory InformationLimitations of Warranty Product WarrantyProduct Warranty Contact Information