Miller Electric 300, 225 manual Duty Cycle Charts, For AC/DC Models, For AC Models, Void warranty

Page 15

4-2. Duty Cycle Charts

A. For AC/DC Models

 

 

 

Duty Cycle is percentage of 10 minutes

 

 

 

that unit can weld at rated load without

 

 

 

overheating.

 

 

 

Y 20% Duty Cycle at 225 Amperes. Ex-

 

 

 

ceeding duty cycle can damage unit

 

 

 

and void warranty.

2 Minutes Welding

8 Minutes Resting

 

A. For 115/230, 230, And 460 Volt Models

B.

For 220, 230/400, And 460 Volt Models

(225/150 Amperes*)

 

 

(300/200 Amperes)

*These models have a 15% duty cycle when used with 50 Hz input power.

086 727 / 099 602-A

B. For AC Models

 

Duty Cycle is percentage of 10 minutes

 

that unit can weld at rated load without

 

overheating.

 

Y 20% Duty Cycle at 225 Amperes. Ex-

 

ceeding duty cycle can damage unit

2 Minutes Welding

and void warranty.

8 Minutes Resting

A. For 115/230 And 230 Volt Models

B. For 220, And 230/400 Volt Models

(225 Amperes*)

(300 Amperes)

*These models have a 15% duty cycle when used with 50 Hz input power.

001 836-A / 099 603-A

OM-316 Page 11

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Stick Smaw Welding ProcessesDescription Visit our website at OM-316087 083Q AugustFrom Miller to You Table of Contents Page Electric Shock can kill Symbol UsageMarks a special safety message Arc Welding HazardsBuildup of GAS can injure or kill ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal can injure eyesCalifornia Proposition 65 Warnings Principal Safety Standards EMF InformationAbout Pacemakers LES Fumées ET LES GAZ peuvent être dangereux Signification des symboles− Consignes DE Sécurité − À Lire Avant Utilisation LES Décharges Électriques peuvent être mortellesLE Bruit peut affecter l’ouïe LE Soudage peut causer un incen- die ou une explosionLES Particules Projetées peu- vent blesser les yeux LES Pièces Chaudes peuvent cau- ser des brûlures gravesLES Pièces Mobiles peuvent cau- ser des blessures Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser ’EMPLOI Excessif peut FaireConsignes relatives aux stimulateurs cardiaques Principales normes de sécuritéInformation sur les champs électromagnétiques Rexdale, Rexdale Ontario Canada M9W 1R3 téléphoneSymbols And Definitions − DefinitionsManufacturer’s Rating Labels AC Models − InstallationSpecifications AC/DC ModelsFor AC Models Duty Cycle ChartsVoid warranty For AC/DC ModelsVolt-Ampere Curves For 115/230, 230 And 460 Volt Models 225/150 AmperesFor 220, 230/400, And 460 Volt Models 300/200 Amperes For 115/230 And 230 Volt Models 225 Amperes For 220 Volt Model For 230/400 Volt Model AmperesAC Amperes 18 in 457 mm for airflow Selecting a LocationWeld Output Cables Installing Electrode Holder And Work ClampInstalling Electrode Cable and Barrel onto Electrode Holder Installing Work Cable onto Work Clamp150 Electrical Service Guide115 220 230 400 460 47.5Wrapper Remove wrapper Jumper Leads Turn Off unit and disconnect input power10 115 V Input Power Cord White Lead Tools Needed 16, 3/8 Cut tie wrapsConnected For 400 Volts Connected For 230 Volts Connecting Input Power For DC Weld Output − OperationControls Controls For AC/DC ModelsControls For AC Models Months − Maintenance & TroubleshootingRoutine Maintenance Lubricating Shunt Block And Anti-Noise AdjustmentReinstalling Amperage Adjustment Indicator Wrapper Remove wrapper from unit Crank Handle Shunt ShaftTorx Trouble Remedy TroubleshootingCircuit Diagram For AC/DC 230 Volts Models − Electrical DiagramsCircuit Diagram For AC/DC 115/230 Volts Models Circuit Diagram For 300/200 AC/DC 230/400 Volts Models Circuit Diagram For 225 230 Volts Models Circuit Diagram For 300 220 Volts Models Welding Methods Shielded Metal Arc Welding Smaw Procedure − Welding Methods & TroubleshootingElectrode And Amperage Selection Chart Striking An Arc Positioning The Electrode Holder10−30 Arc Length Weld Bead CharacteristicsConditions That Affect Weld Bead Shape Electrode AngleTack Welds Electrode Movement During WeldingButt Joints Do not let weave widthPorosity Welding TroubleshootingLap Joints Tee JointsExcessive Spatter Incomplete FusionLack Of Penetration Distortion Excessive PenetrationBurn-Through Waviness Of BeadMain Assembly AC/DC model illustrated − Parts ListMain Assembly Page Work like a Pro TM-188 304 Invision 354MP Service Your distributor also givesSupport Transportation Department Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s
Top Page Image Contents