Multi-Tech Systems MT5634ZLX 2 manual Changing the Remote Escape Character, Remote Configuration

Page 47

Chapter 4 - Remote Configuration

Changing the Remote Escape Character

To increase security, you can change a remote modem’s remote configuration escape character. The remote configuration escape character is stored in register S9. The factory default is 37, which is the ASCII code for the percent character (%). Setting S9 to 0 (zero) disables remote configuration entirely—but if you do this remotely, you won’t be able to change it back remotely!

1.Establish a remote configuration link with the remote modem as described in “Basic Procedure.”

2.Type ATS9=n, where n is the ASCII code for the new remote configuration escape character, then press ENTER.

3.Save the new value by typing AT&W and clicking ENTER.

4.Type ATO<CR> to exit remote configuration.

MT5634ZLX/E

47

Image 47
Contents User Guide Models MT5634ZLX/E and MT5634ZLX/E-T/2Revision Description User GuideContents Index EMC, Safety and Terminal Directive ComplianceIntroduction and Description MultiMobile User Guide IntroductionProduct Description Technical Specifications Features System Requirements MultiMobile User Guide Quick Start Unpacking Safety Warning TelecomMT5634ZLX/E Installation Windows 98 Installation Installing Driver and Modem SoftwareQuick Start MT5634ZLX/E Windows 95 Installation Click My Computer Control Panel and double-clickModems Open My Computer Control Panel Network Windows NT 4.0 InstallationPre-installation Instructions MT5634ZLX/E Installation in NTMT5634ZLX/E Modem configuration for NT Click Have Disk Quick Start MT5634ZLX/E Windows NT 3.51 Installation · TCP/IP For Non-Windows 95/98/NT Systems Artisoft Lantastic 6.0 InstallationNovell NetWare Installation PROTOCOL.INI MS LAN Manager InstallationSelect Enhanced mode NDIS3 for.... then click OK Packet Driver InstallationWindows for Workgroups 3.11 Installation Basic Modem Operation Understanding AT CommandsUsing Windows 95/98/NT HyperTerminal Program Dialing and Answering Techniques MT5634ZLX/E AT Commands, S-Registers and Result Codes AT&K3H0Enter How To Use AT CommandsAT Commands, S-Registers, and Result Codes Basic AT Commands Speaker off during dialing and on until carrier present AT Commands, S-Registers, and Result Codes Remote digital loopback test, in normal mode MT5634ZLX/E Terse Verbose Description Result CodesRegisters MT5634ZLX/E MT5634ZLX/E MT5634ZLX/E Remote Configuration Changing the Setup Password Basic ProcedureSetup Changing the Remote Escape Character Remote ConfigurationMT5634ZLX/E Troubleshooting Characters on the Screen Are Doubled Modem Goes Off-Hook and Disables the Telephone LineModem Does Not Auto-Answer the Phone Communications Software Dials, but Fails Troubleshooting No Text Appears on the Screen in Data ModeNo Text Appears on the Screen When in Command Mode Modem Loses the Connection When in UseConnect Modem Gets Random Errors in Transmitted DataSelect Use Plug and Play Installing The Win 95 Driver Over SystemSoft CardWorksEnabling The MT5634ZLX/E Select Properties Select Drivers in PropertiesWindows NT 3.51 and NT COM Port and IRQ ConflictsWindows Windows 95/98Appendices Industry Canada Appendix a Regulatory ComplianceClass B Statement FCC Part Appendices FCC Part 68 TelecomCanadian Limitations Notice FAX Branding StatementNew Zealand Telecom Warning Notice EMC, Safety and Terminal Directive ComplianceCommission Decision CTR21 Introduction TroubleshootingAppendix B V.90 Support Lmndisnif Drivername LMNDIS$ Appendix C Comprehensive Driver Notes IntroductionNDIS2 Driver for Windows for Workgroups ODI Driver for Workgroups Online Warranty Registration Appendix D Warranty, Service, and Technical SupportLimited Warranty If you don’t know the file name Technical SupportMulti-Tech BBS If you know the file nameAbout the Internet About the MultiMobile SoftGSM Cellular UpgradeSupplyNet Online Ordering Instructions About Ordering AccessoriesAppendix E Uninstalling in Windows 98/95/NT Index IndexMultiMobileUSB User Guide