Multi-Tech Systems MT3334HD8 manual FCC Fax Warning, Canadian Limitations Notice

Page 4

FCC Fax Warning

The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each page or the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual.

See your fax software manual for setup details.

Canadian Limitations Notice

Notice: The ringer equivalence number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination of an interface may consist of any combination of devices subject only to the requirement that the sum of the ringer equivalence numbers of all the devices does not exceed 5.

Notice: The Industry Canada label identifies certificated equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. Industry Canada does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

iv

CommPlete Communications Server

Image 4
Contents MT3334HD8 Modem User Guide Multi-Tech Systems, Inc Woodale Drive Mounds View, Minnesota CommPlete Communications Server FCC Fax Warning Canadian Limitations NoticeTable of Contents Testing the MT3334HD8 Warranty, Service, and Technical SupportAppendix D Appendix FIntroduction LED Indicators Power SuppliesIntroduction Manual OrganizationInstallation Technical Specifications Data Rates ModemIntroduction 2400 & 1200 bps MT3334HD8 User Guide Power Installation Safety Warnings MT3334HD8 modem cardPre-Installation Notes Installation ProcedurePage AT Commands Command Structure Working with AT CommandsModes of Operation Command Editing AT Commands by Function $BA Dialing Commands Dial Modifier CommandsDs Dial Continuous RedialPulse or Tone Dialing Wait for New Dial ToneRn Reverse Originate/Answer Mode Return to Command Mode After DialingDialing Pause Flash On-HookPhone Number Memory Commands @ Quiet AnswerCall Card Tone Detect DsNd Store a Phone NumberConfiguration Storage and Recall Commands Wn Store ConfigurationNdNe Number Linking List Stored Telephone NumbersFn Load Default Configuration Modem Response Result Code CommandsReset Modem Echo Command Mode Characters Result Codes Verbose/Terse Online Connection Commands An Answerback#An Auto Speed Detection Bn Answer ToneCDn Cleardown at Disconnect DCn AT Command ControlDTn Dtmf Detection #Fn Fallback Modes Gn Guard TonesHn Busy-Out After Disconnect Pn Set Pulse-Dial Ratios$Tn Calling Tone RDn Square Wave Ring Detect#Tn Trellis-Coded Modulation Commands Fn Echo Canceler Frequency Offset CompensationYn Long Space Disconnect RAn Asymmetric Bit RateCn Carrier Detect Control RS-232 Interface CommandsDn Data Terminal Ready Control Rn Clear to Send Control Sn Data Set Ready ControlRFn CTS/RTS Interaction Control SFn DSR/CD Interaction ControlError Correction and Data Compression Commands En Error Correction Modes#Ln V.42 Error Correction Modes En Data Compression$Fn Auto-Reliable Fallback Character Enable/Disable $En V.42 Error Correction at 300 bps$An Auto-Reliable Buffering $BAn Baud Adjust Speed Conversion Commands$Rn Retransmit Count $MBn Modem Baud Rate $SBn Serial Port Baud RateImmediate Action Commands Repeat Last CommandInquire Product Code L5, L7 List Current Operating ParametersFlow Control Commands E3 Flow Control Disable En Non-Error Correction Mode Flow ControlE4 Hardware Flow Control E5 XON/XOFF Flow ControlEn Pacing Computer-Initiated Flow Control #Xn Number of Xoff Characters SentForce Answer Mode Escape Sequences+++ATCR In-Band Escape Sequence Breakatcr Out-of-Band Escape SequenceRemote Configuration Commands Atcr Remote Configuration Escape Sequence#Ixxxxxx Change Login Password Go Back OnlineLine Probe Commands #Syyyyyy Change Setup PasswordDPn Read Line Probe Data DFn Format Line Probe DataDiagnostic Commands Tn Respond to Remote Digital Loopback SignalRP Immediate Line Probe Ln Display Line Probe DataUn Loopback Test Modes MT3334HD8 User Guide Registers Registers S0 Number of Rings Until Modem AnswersS1 Ring Count S2 Escape Code CharacterS7 Time for Carrier Abort Timer S4 Line Feed CharacterS5 Backspace Character S6 Wait Time for Dial ToneS10 Carrier Loss Disconnect Delay Time S13 Remote Configuration Escape CharacterS9 Carrier Detect Response Time S11 Tone Dialing Spacing and DurationS30 Inactivity Timer S34 Command Buffer Length After Online Escape SequenceS24 PBX/CBX Disconnect Drop Time for DSR/CTS/CD S25 DTR Dropout TimeS94 Out-of-Service Time S37 DTR Busy-In TimeS43 Force V.34 Connect Speed S48 Maximum V.34 Connect SpeedAT Commands that Affect S-Registers Reading and Assigning S-Register ValuesExamples of Assigning Values Examples of Reading ValuesAT&E2$SP1#L3$R0$MB19200$SB115200$EB1S0=10&W0CR Testing the MT3334HD8 Test procedure Local Analog Loopback Test V.54 LoopTesting the MT3334HD8 Remote Digital Loopback Test V.54 LoopDial the remote modem and establish your online connection Local Digital Loopback Test V.54 Loop Local digital loopback testPage Warranty, Service, and Technical Support Limited Warranty ServiceTechnical Support Recording Product InformationLogging onto the Multi-Tech BBS Multi-Tech BBSDownloading a File About CompuServe Reading a MessageLeaving a Message BulletinsAbout the Multi-Tech Fax-Back Service About the InternetUsing FlashPro to Upgrade Firmware Upgrading the MT3334HD8 FirmwareMT3334HD8 User Guide Appendixes Appendix a Ascii Conversion Chart Ctrl Code HEX DECDial Pulses Appendix B Dial Pulses and TonesTone Dial Frequencies Figure B-2. Standard Dtmf frequencies Appendix C Result Code Summary Multi-Tech Result Codes &Q0Standard AT Result Codes &Q1 Register Unit Range Default Description Appendix D S-Register SummarySets fixed V.34 connect speed = 28800 bps Appendix E AT Command Summary ReturnCDn AT Command Summary $Fn Command Values Description Command Values Description $MBn RAn Command Values Description SFn Command Values Description #Vn Breakatcr Basic Procedure Appendix F Remote ConfigurationSetup Changing the Passwords Changing the Remote Escape CharacterIndex MT3334HD8 User Guide Index Long space break Pacing, 36, 37, 38 enable/disable, 38 ENQ/ACK Commands Loopback tests, 42, 43, 54, 56 tone detection