Multi-Tech Systems FR3060, FR3100, FR3060/V4, FR3060/V8, FR3100/V4, FR3100/V8 manual

Page 17

Chapter 2 - Installation

Voice/Fax Cable Connections

NOTE: The E&M, FXS, and Ethernet ports are not designed to be connected to a Public Telecommunication Network.

6If you are connecting a station device; e.g., analog telephone, fax machine, or Key Telephone System (KTS) to your MultiFRAD; connect one end of an RJ-11 phone cord to the Voice/Fax Channel 1 FXS connector on the back of the MultiFRAD and the other end to the station device. See Figure 5.

VOICE/

VOICE/

VOICE/

VOICE/

FAX

FAX

FAX

FAX

CHANNEL

CHANNEL

CHANNEL

CHANNEL

8

7

6

5

E&M

FXO

FXS

E&M

FXO

FXS

E&M

FXO

FXS

E&M

FXO

FXS

VOICE/

VOICE/

VOICE/

VOICE/

FAX

FAX

FAX

FAX

CHANNEL

CHANNEL

CHANNEL

CHANNEL

4

3

2

1

CHANNEL

10

CHANNEL

8

CHANNEL

6

CHANNEL

4

CHANNEL

2 (RS232/V.35)

CHANNEL

9

CHANNEL

7

CHANNEL

5

CHANNEL

3

CHANNEL

1 (RS232/V.35)

10BASET	COMMAND PORT
ETHERNET	EXT. COMPOSITE LINK (RS232/V.35)

INTERNAL

COMPOSITE

LINK MONITOR XMT RCV

T1 DSU

GND

I

POWER O

Voice/Fax Channel 1 - 8

Connections

E&M FXO FXS

E&M

FXO

FXS

PSTN

Figure 5. Voice/Fax Cable Connections

If you are connecting the station side of a telephone switch (PBX) to your MultiFRAD, connect one end of an RJ-11 phone cord to the Voice/Fax Channel 1 FXO connector on the back of the MultiFRAD and the other end to the phone jack.

If you are connecting an E&M trunk from a telephone switch to your MultiFRAD, connect one end of an RJ-45 phone cord to the Voice/Fax Channel 1 E&M connector on the back of the MultiFRAD and the other end to the trunk phone jack.

If you are connecting to an E&M trunk, you need to ensure that the E&M trunk jumper is in the correct position for the E&M type trunk. The default E&M jumper position is E&M type 2. To change the E&M jumper position, perform the E&M jumper block positioning procedure in following this procedure.

7Repeat the above step to connect the remaining telephone equipment to each Voice/Fax Channel on your MultiFRAD.

8Turn on power to the MultiFRAD by placing the On/Off switch on the back panel to the 1 position.

At this time your MultiFRAD is completely cabled. Proceed to the next section to load your software.

17

Image 17

Contents User Guide Record of Revisions RevisionDescription User GuideContents Appendices Introduction and Description MultiFRAD 3000-Series IntroductionPreview of this Guide Ethernet Front Panel DescriptionComposite Link Voice/Fax Channels 1 Channels 1Channels 3 through Frame Ground GND Connector Power ConnectorInternal Composite Link T1 DSU Connector Monitor XMT/RCV ConnectorVoice/Fax Channels 1 8 Connectors Channels 3 10 ConnectorsCommand Port Technical SpecificationsChannel Connectors Voice/Fax Channel ConnectorsInstallation Unpacking your MultiFRAD Safety WarningsCabling your MultiFRAD Valid Voice/Fax ChannelsChannel Cable Connections Voice/Fax Cable Connections Default Jumper Block Positioning ProcedureSoftware Loading and Configuration Loading your Software Software Loading and Configuration MultiFRAD 3000-Series User Guide IP Address Ethernet Mask Frame Type MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Detect and Map Your DLCIs MultiFRAD 3000-Series User Guide Build Your Phone Directory Database MultiFRAD 3000-Series User Guide Click Download Setup MultiFRAD 3000-Series User Guide MultiFRAD Software Before You Begin MultiFRAD Configuration Changing IP Parameters MultiFRAD Software MultiFRAD 3000-Series User Guide Changing IPX Parameters MultiFRAD 3000-Series User Guide MultiFRAD Software Changing Bridging Parameters WAN Port Setup Point to Point Setup Frame Relay Setup MultiFRAD 3000-Series User Guide MultiFRAD Software MultiFRAD 3000-Series User Guide MultiFRAD Software Data Port Configuration FXS Interface Changing Voice/Fax Channel ParametersInterface Interface Voice/FaxFXO Interface Regional Changing the Phone Directory Database Others Setup Enable Logging of Statistics Statistics IP Statistics STP Spanning Tree Port Statistics IPX Port StatisticsWAN Statistics Snmp StatisticsPPP Statistics Data Port Statistics Frame Relay Statistics MultiFRAD 3000-Series User Guide Remote Configuration and Management Modem-Based Remote ConfigurationRemote Configuration and Management LAN-Based Warranty, Service and Tech Support Telnet Remote ManagementMultiFRAD Management Menu MultiFRAD ConfigurationRemote User Database WEB Browser ManagementRemote Configuration and Management MultiFRAD 3000-Series User Guide Warranty, Service and Tech Support On-line Warranty Registration Limited WarrantyContacting Tech Support via E-mail Tech SupportRecording MultiFRAD Information Multi-Tech BBS ServiceTo log on to the Multi-Tech BBS To Download a fileIf you don’t know the file name About the InternetMultiFRAD 3000-Series User Guide Appendices LAN Cables Appendix a Cabling Diagrams Command Port CableVoice/Fax Channel Connectors RS232C/V.24 * Link Cable Trunk CableCommand Port Remote Configuration CableAppendix B Regulatory Information Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary 100 101 102 103 Index Remote Configuration

Related manuals

Manual 105 pages 17.07 Kb