Multi-Tech Systems FR3060, FR3100/V8 manual MultiFRAD Software

Page 51

Chapter 4 - MultiFRAD Software

When you click the OK button, the new DLCI appears in the DLCI’s window in the Frame Relay DLCI dialog box.

When a DLCI has just been detected, or if you have just made a new DLCI, no data ports and protocols are mapped to it. The default Congestion Management, mode, CIR, and Be are displayed. You should verify these default settings with how your new DLCI is provisioned by you service provider.

Congestion Management, Mode, and CIR/Be settings are used to avoid congestion and possible loss of data. The Committed Information Rate (CIR) and Excess Burst rate (Be) settings are throughput amounts determined by the network and user when each DLCI is ordered. The CIR is the basic throughput which the network will try to set aside for that DLCI. It will always be equal to or less than the actual access rate of the physical line (i.e., if the frame relay physical link is a 56K DDS line, the sum of the CIRs of all DLCIs on that link should not exceed 56K bps). The Be is the excess burst throughput rate (added to CIR) that the network should accept for that DLCI before significant loss of data occurs due to the discarding of frames during times of congestion. Note, however, that in frame relay there is no absolute guarantee of a congestion-free link, regardless of CIR and Be settings. The CIR and Be settings on the MultiFRAD should match the settings that the network has provisioned.

The Congestion Management and Mode settings determine how the MultiFRAD handles congestion. The Mode selects whether the MultiFRAD should use its own throughput calculations to avoid congestion, or simply send data to the network as fast as possible. The MultiFRAD calculates throughput after every CIR Measurement Interval, and can limit throughput to either the CIR (Adhere to CIR) or the CIR plus the Be (Adhere to CIR+Be). The Congestion Management setting selects whether the MultiFRAD should stop sending data when congestion is indicated (Stop and Start), or gradually reduce throughput during times of congestion (Throttle Up and Down).

51

Image 51

Contents User Guide Record of Revisions RevisionDescription User GuideContents Appendices Introduction and Description MultiFRAD 3000-Series IntroductionPreview of this Guide Front Panel Description Composite LinkEthernet Channels 1 Channels 3 throughVoice/Fax Channels 1 Monitor XMT/RCV Connector Power ConnectorFrame Ground GND Connector Internal Composite Link T1 DSU ConnectorVoice/Fax Channels 1 8 Connectors Channels 3 10 ConnectorsVoice/Fax Channel Connectors Technical SpecificationsCommand Port Channel ConnectorsInstallation Unpacking your MultiFRAD Safety WarningsCabling your MultiFRAD Valid Voice/Fax ChannelsChannel Cable Connections Voice/Fax Cable Connections Default Jumper Block Positioning ProcedureSoftware Loading and Configuration Loading your Software Software Loading and Configuration MultiFRAD 3000-Series User Guide IP Address Ethernet Mask Frame Type MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Detect and Map Your DLCIs MultiFRAD 3000-Series User Guide Build Your Phone Directory Database MultiFRAD 3000-Series User Guide Click Download Setup MultiFRAD 3000-Series User Guide MultiFRAD Software Before You Begin MultiFRAD Configuration Changing IP Parameters MultiFRAD Software MultiFRAD 3000-Series User Guide Changing IPX Parameters MultiFRAD 3000-Series User Guide MultiFRAD Software Changing Bridging Parameters WAN Port Setup Point to Point Setup Frame Relay Setup MultiFRAD 3000-Series User Guide MultiFRAD Software MultiFRAD 3000-Series User Guide MultiFRAD Software Data Port Configuration Changing Voice/Fax Channel Parameters InterfaceFXS Interface Voice/Fax FXO InterfaceInterface Regional Changing the Phone Directory Database Others Setup Enable Logging of Statistics Statistics IP Statistics STP Spanning Tree Port Statistics IPX Port StatisticsWAN Statistics Snmp StatisticsPPP Statistics Data Port Statistics Frame Relay Statistics MultiFRAD 3000-Series User Guide Remote Configuration and Management Modem-Based Remote ConfigurationRemote Configuration and Management LAN-Based Warranty, Service and Tech Support Telnet Remote ManagementMultiFRAD Management Menu MultiFRAD ConfigurationRemote User Database WEB Browser ManagementRemote Configuration and Management MultiFRAD 3000-Series User Guide Warranty, Service and Tech Support On-line Warranty Registration Limited WarrantyTech Support Recording MultiFRAD InformationContacting Tech Support via E-mail To Download a file ServiceMulti-Tech BBS To log on to the Multi-Tech BBSIf you don’t know the file name About the InternetMultiFRAD 3000-Series User Guide Appendices LAN Cables Appendix a Cabling Diagrams Command Port CableVoice/Fax Channel Connectors RS232C/V.24 * Link Cable Trunk CableCommand Port Remote Configuration CableAppendix B Regulatory Information Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary 100 101 102 103 Index Remote Configuration

Related manuals

Manual 105 pages 17.07 Kb