Multi-Tech Systems FR3060, FR3100/V8 manual Jumper Block Positioning Procedure, Default

Page 18

MultiFRAD 3000-Series User Guide

E&M Jumper Block Positioning Procedure

A jumper block exists for each voice/fax channel. The jumper block is to the right of each set of channel jacks. The jumper block contains 8-pairs of pins. The jumper plug fits over three pairs of pins on the jumper block. The E&M type number is labeled on the pc board. The jumper plug needs to be centered on the E&M type number. Perform the following procedure to change E&M jumper position.

1Ensure that power is removed from the MultiFRAD.

2Turn the unit up side down and remove the four phillips screws from the cover. Turn the unit right side up and remove the four phillips screws from the back of the top cover.

3Remove the front panel by loosening the two capative phillips screws. Slide the top cover back off the chassis to expose the rear panel.

4To change a jumper position, lift the jumper plug up off the jumper block and move to the new position, ensuring that the center jumper is centered on the E&M type number.

2 (Default)

1,3

4

5

Figure 6. E&M Jumper Block

5Change the jumper position for each voice/fax channel that is connecting to an E&M trunk that is not a type 2.

6Slide the top cover back on to the chassis. Replace the front panel and secure it by tightening the two capative phillips screws.

7From the back of the unit, replace the four phillips screws that secure the top cover. Then, turn the unit up side down and replace the four phillips that secure the top cover.

8Return to your General Cabling Connections Procedure.

18

Image 18

Contents User Guide User Guide Record of Revisions RevisionDescriptionContents Appendices Introduction and Description Introduction MultiFRAD 3000-SeriesPreview of this Guide Front Panel Description Composite LinkEthernet Channels 1 Channels 3 throughVoice/Fax Channels 1 Internal Composite Link T1 DSU Connector Power ConnectorFrame Ground GND Connector Monitor XMT/RCV ConnectorChannels 3 10 Connectors Voice/Fax Channels 1 8 ConnectorsChannel Connectors Technical SpecificationsCommand Port Voice/Fax Channel ConnectorsInstallation Safety Warnings Unpacking your MultiFRAD Valid Voice/Fax Channels Cabling your MultiFRADChannel Cable Connections Voice/Fax Cable Connections Jumper Block Positioning Procedure DefaultSoftware Loading and Configuration Loading your Software Software Loading and Configuration MultiFRAD 3000-Series User Guide IP Address Ethernet Mask Frame Type MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Detect and Map Your DLCIs MultiFRAD 3000-Series User Guide Build Your Phone Directory Database MultiFRAD 3000-Series User Guide Click Download Setup MultiFRAD 3000-Series User Guide MultiFRAD Software Before You Begin MultiFRAD Configuration Changing IP Parameters MultiFRAD Software MultiFRAD 3000-Series User Guide Changing IPX Parameters MultiFRAD 3000-Series User Guide MultiFRAD Software Changing Bridging Parameters WAN Port Setup Point to Point Setup Frame Relay Setup MultiFRAD 3000-Series User Guide MultiFRAD Software MultiFRAD 3000-Series User Guide MultiFRAD Software Data Port Configuration Changing Voice/Fax Channel Parameters InterfaceFXS Interface Voice/Fax FXO InterfaceInterface Regional Changing the Phone Directory Database Others Setup Enable Logging of Statistics Statistics IP Statistics IPX Port Statistics STP Spanning Tree Port StatisticsSnmp Statistics WAN StatisticsPPP Statistics Data Port Statistics Frame Relay Statistics MultiFRAD 3000-Series User Guide Remote Configuration and Management Remote Configuration Modem-BasedRemote Configuration and Management LAN-Based Warranty, Service and Tech Support Remote Management TelnetMultiFRAD Configuration MultiFRAD Management MenuWEB Browser Management Remote User DatabaseRemote Configuration and Management MultiFRAD 3000-Series User Guide Warranty, Service and Tech Support Limited Warranty On-line Warranty RegistrationTech Support Recording MultiFRAD InformationContacting Tech Support via E-mail To log on to the Multi-Tech BBS ServiceMulti-Tech BBS To Download a fileAbout the Internet If you don’t know the file nameMultiFRAD 3000-Series User Guide Appendices Appendix a Cabling Diagrams Command Port Cable LAN CablesVoice/Fax Channel Connectors Trunk Cable RS232C/V.24 * Link CableRemote Configuration Cable Command PortAppendix B Regulatory Information Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary 100 101 102 103 Index Remote Configuration

Related manuals

Manual 105 pages 17.07 Kb