Multi-Tech Systems FR3060, FR3100/V8 manual MultiFRAD 3000-Series User Guide

Page 42

MultiFRAD 3000-Series User Guide

The Routing option is normally checked; however, if you do not wish to have IP packets routed, then uncheck this item. If IP routing is disabled and bridging is enabled, IP packets are bridged; i.e., IP packets are transferred.

The RIP option enables RIP based routing. RIP (Routing Information Protocol) is a protocol used among MultiFRADs to exchange routing table information. RIP is the most common protocol used in both IP and IPX networks. It is also used internally by client workstations in IPX networks to obtain routes (shortest, or otherwise) to any distant network. RIP based routing should normally be enabled. It can be disabled, however, if you are using WAN links in Dial on Demand mode. For DOD links, disabling RIP will reduce traffic on the link as it will also disable periodic RIP broadcasts. RIP routing on a given port will be automatically turned off when Dial on Demand is enabled on the PPP Port Setup tab for the WAN port.

The Default TTL text box defines the IP Time-To-Live parameter that sets the maximum number of hops a frame may travel before being dropped. This is used to limit errant frames such as those that may arise under circularly defined networks. Recommended value is decimal 255.

The RIP Response Time text box defines the time interval between periodic RIP broadcasts. Regular RIP broadcasts are required to keep the routing tables of all MultiFRADs in the internetwork consistent. Increasing the frequency of these broadcasts may consume precious bandwidth that could have been used for transfer of other regular packets and has a recommended value of 30 seconds.

The Reassembly Timeout text box defines the amount of time the IP routing software will wait for all the fragments of an IP datagram to arrive before discarding the partially reassembled datagram and has a recommended value of 30 seconds.

The RIP Route Aging Time text box defines the time interval that must expire before an unused route entry created by RIP is aged from the route table. The aging timer starts from the addition, reference, or change of an RIP based routed entry and has a recommended value of 180 seconds.

The Dynamic Host Configuration Protocol (DHCP) group is not supported on this product.

The MultiFRAD supports Domain Name System (DNS) group is not support on this product.

The Default Route group defines the default route for the MultiFRAD. The IP Address field specifies the full 32-bit IP host address of the next hop for packets being forwarded via default routing. The MultiFRAD will automatically resolve the IP address to a port number via its IP route table. The Metric defines the number of hops to the specified IP address and is typically set to a value of 1. If the default route is for an unnumbered link, select the port from the Port combo box. Finally, whenever you set up default routing, be sure to disable RIP based routing.

The Static Routes button displays a dialog box that enables you to view, add, edit, or delete static routes to a target IP address (which can be the address of an IP host, an IP network, or an IP subnetwork). You must specify the target host IP address and the Gateway Address in dotted decimal form. The Gateway Address is the IP address of the MultiFRAD that is the next hop toward the target host. The address mask is the subnet mask of the target IP host, and the Metric is the hop count to the target host or subnet and can be either 0 or 1.

42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents User Guide User Guide Record of Revisions RevisionDescriptionContents Appendices Introduction and Description Introduction MultiFRAD 3000-SeriesPreview of this Guide Front Panel Description Composite LinkEthernet Channels 1 Channels 3 throughVoice/Fax Channels 1 Internal Composite Link T1 DSU Connector Power ConnectorFrame Ground GND Connector Monitor XMT/RCV ConnectorChannels 3 10 Connectors Voice/Fax Channels 1 8 ConnectorsChannel Connectors Technical SpecificationsCommand Port Voice/Fax Channel ConnectorsInstallation Safety Warnings Unpacking your MultiFRADValid Voice/Fax Channels Cabling your MultiFRADChannel Cable Connections Voice/Fax Cable Connections Jumper Block Positioning Procedure DefaultSoftware Loading and Configuration Loading your Software Software Loading and Configuration MultiFRAD 3000-Series User Guide IP Address Ethernet Mask Frame Type MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Detect and Map Your DLCIs MultiFRAD 3000-Series User Guide Build Your Phone Directory Database MultiFRAD 3000-Series User Guide Click Download Setup MultiFRAD 3000-Series User Guide MultiFRAD Software Before You Begin MultiFRAD Configuration Changing IP Parameters MultiFRAD Software MultiFRAD 3000-Series User Guide Changing IPX Parameters MultiFRAD 3000-Series User Guide MultiFRAD Software Changing Bridging Parameters WAN Port Setup Point to Point Setup Frame Relay Setup MultiFRAD 3000-Series User Guide MultiFRAD Software MultiFRAD 3000-Series User Guide MultiFRAD Software Data Port Configuration Changing Voice/Fax Channel Parameters InterfaceFXS Interface Voice/Fax FXO InterfaceInterface Regional Changing the Phone Directory Database Others Setup Enable Logging of Statistics Statistics IP Statistics IPX Port Statistics STP Spanning Tree Port StatisticsSnmp Statistics WAN StatisticsPPP Statistics Data Port Statistics Frame Relay Statistics MultiFRAD 3000-Series User Guide Remote Configuration and Management Remote Configuration Modem-BasedRemote Configuration and Management LAN-Based Warranty, Service and Tech Support Remote Management TelnetMultiFRAD Configuration MultiFRAD Management MenuWEB Browser Management Remote User DatabaseRemote Configuration and Management MultiFRAD 3000-Series User Guide Warranty, Service and Tech Support Limited Warranty On-line Warranty RegistrationTech Support Recording MultiFRAD InformationContacting Tech Support via E-mail To log on to the Multi-Tech BBS ServiceMulti-Tech BBS To Download a fileAbout the Internet If you don’t know the file nameMultiFRAD 3000-Series User Guide Appendices Appendix a Cabling Diagrams Command Port Cable LAN CablesVoice/Fax Channel Connectors Trunk Cable RS232C/V.24 * Link CableRemote Configuration Cable Command PortAppendix B Regulatory Information Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary 100 101 102 103 Index Remote Configuration
Related manuals
Manual 105 pages 17.07 Kb
Top Page Image Contents