Multi-Tech Systems FR3060, FR3100/V8 manual Data Port Configuration

Page 54

MultiFRAD 3000-Series User Guide

Data Port Configuration

The Data Port Configuration dialog box allows you to change the parameters of the data transferred between the data device and the MultiFRAD. The MultiFRAD can transfer data between the data device and MultiFRAD in either synchronous or asynchronous mode. If your data device is an asynchronous device, choose the Configure Asynchronous option and configure the MultiFRAD to match your device. If the data device is a synchronous device, choose the Configure Synchronous option and configure the MultiFRAD to match your synchronous device. The Data Port Configuration dialog box also allows you to configure each channel independently.

For example, port 1 could be connected to a Multi-Tech MultiMux MMH904. In this situation, port 1 could be configured with the following options:

•Data Port Mode set to APSM (Advanced Priority Statistical Multiplexing),

•Synchronous Configuration,

•Internal Clocking with Speed set to 19200,

•Encoding Scheme set to NRZ for all Multi-Tech Muxes,

•Between Frames set to Send Flags, and

•InterFrame Timer (in ms) has to be off.

The MMH904 would have to be configured for an external composite link device. This means that the 8-position DIP Switch on the MMH904 would have to be toggled to the closed position and an external composite link cable connected between the MMH904 and the MultiFRAD Channel connector.

In most applications, the encoding scheme, interframe timer, and between frames will be used at their default settings. If you are unsure of your device’s configuration, start with the defaults or refer to your device’s documentation.

54

Image 54

Contents User Guide User Guide Record of Revisions RevisionDescriptionContents Appendices Introduction and Description Introduction MultiFRAD 3000-SeriesPreview of this Guide Front Panel Description Composite LinkEthernet Channels 1 Channels 3 throughVoice/Fax Channels 1 Internal Composite Link T1 DSU Connector Power ConnectorFrame Ground GND Connector Monitor XMT/RCV ConnectorChannels 3 10 Connectors Voice/Fax Channels 1 8 ConnectorsChannel Connectors Technical SpecificationsCommand Port Voice/Fax Channel ConnectorsInstallation Safety Warnings Unpacking your MultiFRADValid Voice/Fax Channels Cabling your MultiFRADChannel Cable Connections Voice/Fax Cable Connections Jumper Block Positioning Procedure DefaultSoftware Loading and Configuration Loading your Software Software Loading and Configuration MultiFRAD 3000-Series User Guide IP Address Ethernet Mask Frame Type MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Detect and Map Your DLCIs MultiFRAD 3000-Series User Guide Build Your Phone Directory Database MultiFRAD 3000-Series User Guide Click Download Setup MultiFRAD 3000-Series User Guide MultiFRAD Software Before You Begin MultiFRAD Configuration Changing IP Parameters MultiFRAD Software MultiFRAD 3000-Series User Guide Changing IPX Parameters MultiFRAD 3000-Series User Guide MultiFRAD Software Changing Bridging Parameters WAN Port Setup Point to Point Setup Frame Relay Setup MultiFRAD 3000-Series User Guide MultiFRAD Software MultiFRAD 3000-Series User Guide MultiFRAD Software Data Port Configuration Changing Voice/Fax Channel Parameters InterfaceFXS Interface Voice/Fax FXO InterfaceInterface Regional Changing the Phone Directory Database Others Setup Enable Logging of Statistics Statistics IP Statistics IPX Port Statistics STP Spanning Tree Port StatisticsSnmp Statistics WAN StatisticsPPP Statistics Data Port Statistics Frame Relay Statistics MultiFRAD 3000-Series User Guide Remote Configuration and Management Remote Configuration Modem-BasedRemote Configuration and Management LAN-Based Warranty, Service and Tech Support Remote Management TelnetMultiFRAD Configuration MultiFRAD Management MenuWEB Browser Management Remote User DatabaseRemote Configuration and Management MultiFRAD 3000-Series User Guide Warranty, Service and Tech Support Limited Warranty On-line Warranty RegistrationTech Support Recording MultiFRAD InformationContacting Tech Support via E-mail To log on to the Multi-Tech BBS ServiceMulti-Tech BBS To Download a fileAbout the Internet If you don’t know the file nameMultiFRAD 3000-Series User Guide Appendices Appendix a Cabling Diagrams Command Port Cable LAN CablesVoice/Fax Channel Connectors Trunk Cable RS232C/V.24 * Link CableRemote Configuration Cable Command PortAppendix B Regulatory Information Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary 100 101 102 103 Index Remote Configuration

Related manuals

Manual 105 pages 17.07 Kb