Multi-Tech Systems FR3060, FR3100, FR3060/V4, FR3060/V8, FR3100/V4, FR3100/V8 manual Voice/Fax

Page 56

MultiFRAD 3000-Series User Guide

FXO Interface

The FXO Interface is used to connect PBX extensions or central office telephone lines. You also, need to select DTMF or Pulse dialing in the Regeneration field of the Dialing Options group. If you are unsure of the correct selection, contact the personnel in charge of your PBX or your local telephone company to determine whether pulse or DTMF should be used.

E&M Interface

The E&M Interface is used to connect PBX E&M trunks. You will need to select between Dial Tone or Wink signaling and also between 2-wire and 4-wire mode. If wink signaling is selected, the wink timer field becomes active with a range from 100 to 350 milliseconds. Contact the personnel in charge of your PBX to determine the proper configuration of these settings.

Voice/Fax

The Voice/Fax tab controls the voice coder, Fax settings, DTMF gain, and some miscellaneous options.

The MultiFRAD supports many state-of-the art ITU (International Telecommunications Union) voice standards. The Voice Coder drop-down menu enables you to select from a range of standards with specific bandwidths. The higher the bps rate, the more bandwidth is used. The channel that you are calling has to have the same voice coder selected.

The Fax group enables a fax machine to transmit and receive faxes through the MultiFRAD. If a fax machine is connected to one of the voice/fax channels, the Max Baud Rate should be set to match the baud rate of the fax machine. This setting should be changed only under the direction of Multi- Tech’s Technical Support personnel (see Chapter 6).

56

Image 56

Contents User Guide User Guide Record of Revisions RevisionDescriptionContents Appendices Introduction and Description Introduction MultiFRAD 3000-SeriesPreview of this Guide Ethernet Front Panel DescriptionComposite Link Voice/Fax Channels 1 Channels 1Channels 3 through Power Connector Frame Ground GND ConnectorInternal Composite Link T1 DSU Connector Monitor XMT/RCV ConnectorChannels 3 10 Connectors Voice/Fax Channels 1 8 ConnectorsTechnical Specifications Command PortChannel Connectors Voice/Fax Channel ConnectorsInstallation Safety Warnings Unpacking your MultiFRADValid Voice/Fax Channels Cabling your MultiFRADChannel Cable Connections Voice/Fax Cable Connections Jumper Block Positioning Procedure DefaultSoftware Loading and Configuration Loading your Software Software Loading and Configuration MultiFRAD 3000-Series User Guide IP Address Ethernet Mask Frame Type MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Detect and Map Your DLCIs MultiFRAD 3000-Series User Guide Build Your Phone Directory Database MultiFRAD 3000-Series User Guide Click Download Setup MultiFRAD 3000-Series User Guide MultiFRAD Software Before You Begin MultiFRAD Configuration Changing IP Parameters MultiFRAD Software MultiFRAD 3000-Series User Guide Changing IPX Parameters MultiFRAD 3000-Series User Guide MultiFRAD Software Changing Bridging Parameters WAN Port Setup Point to Point Setup Frame Relay Setup MultiFRAD 3000-Series User Guide MultiFRAD Software MultiFRAD 3000-Series User Guide MultiFRAD Software Data Port Configuration FXS Interface Changing Voice/Fax Channel ParametersInterface Interface Voice/FaxFXO Interface Regional Changing the Phone Directory Database Others Setup Enable Logging of Statistics Statistics IP Statistics IPX Port Statistics STP Spanning Tree Port StatisticsSnmp Statistics WAN StatisticsPPP Statistics Data Port Statistics Frame Relay Statistics MultiFRAD 3000-Series User Guide Remote Configuration and Management Remote Configuration Modem-BasedRemote Configuration and Management LAN-Based Warranty, Service and Tech Support Remote Management TelnetMultiFRAD Configuration MultiFRAD Management MenuWEB Browser Management Remote User DatabaseRemote Configuration and Management MultiFRAD 3000-Series User Guide Warranty, Service and Tech Support Limited Warranty On-line Warranty RegistrationContacting Tech Support via E-mail Tech SupportRecording MultiFRAD Information Service Multi-Tech BBSTo log on to the Multi-Tech BBS To Download a fileAbout the Internet If you don’t know the file nameMultiFRAD 3000-Series User Guide Appendices Appendix a Cabling Diagrams Command Port Cable LAN CablesVoice/Fax Channel Connectors Trunk Cable RS232C/V.24 * Link CableRemote Configuration Cable Command PortAppendix B Regulatory Information Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary 100 101 102 103 Index Remote Configuration

Related manuals

Manual 105 pages 17.07 Kb