Minicom Advanced Systems 108 IP, 108/116 IP manual Restoring Facttory Defaults, To enter Safe mode

Page 58

Troubleshooting – Safe Mode

Restoring Factory Defaults

To enter Safe mode:

1.While powering up Smartt 108/116 IP, press and hold down the Go Loccal button on the back panel of the uniit for three to four seconds.

The device boots up in Safe mode.

2.Wait until the unit finishees booting (one to two minutes).

3.Determine the IP addresss of the Smart 108/116 IP unit. The IP addresss depends on whether or not there is a DHCP server on the network. If there is, the DHCP server assigns an IP address to the Smart 108/116 IP unit. If there is no DHCCP server, the unit boots with the static IP address 192.168.2.155.

4.Open Internet Explorer and type into the Address box: http://IP addreess/config. (Do not start the addresss with https.)

The Login page appears.

Figure 46 – Login Page

5.In User, type username admin , and in Password, type SAFEmode (case sensitive). (This username and password works only in Safe mode.)

A menu appears.

Figure 47 – Safe Mode Menu

5.2 Restoring Facttory Defaults

You can restore all Smart 108/116 IP settings to their default values.

58 Smart 108/116 IP

Page 57 Page 59
Image 58
Page 57 Page 59
Contents Smart 108/116 IP User Guide Legal Notice Chapters and Their Contents About this DocumentArial Bold Video ResolutionStyle Conventions Refresh Rates Snmp Events TableTable of Contents Conducting a Remote Session Troubleshooting Safe Mode Downloading Update Software and Latest Firmware Table of Figures Smart 108/116 IP Unit Front PanelDelete Keys Confirmation Box Introduction Features and BenefitsProduct Overview Compatibility Technical PrecautionsTerminology Client Computer Operating SystemTrademarks SafetyWeee Compliance System Components InstallationOverview Smart 108/116 IP UnitLED/Button Functionality Port FunctionalityRack Mounting the Smart 108/116 IP Unit Pre-Installation GuidelinesRack Mounting Safety Considerations Mounting the UnitConnecting the System To rack mount the Smart 108/116 IP unitConnecting to the Servers Smart 108/116 IP System OverviewConnecting a R ICC/ROC PS/2 To connect the RICC/ROOC PS/2 to a powered on computerConnecting a Ricc SUN Connecting a RICC/ROC USBTo connect the RICC/ROC USB Connecting the CAT5 Cables Connecting to the NetworkConnecting the KVM Console Connecting the Power Supply To connect the power sup ply to Smart 108/116 IPConfiguring the Network Boot-Up ProcessLogging Onto the Web Configuration Interface Assigning Static IP Addresses for a Number of UnitsMode, select Configuration To log into the Web inteerfaceWeb Configuration Interface Tabs Configuring Device ID Settings Configuring the Network SettingsWeb Configuration Toolbar Buttons ButtonFunctionalityTo configure Device ID settings Configuring the D evice IP AddressConfiguring Centrralized Management Settings To configure Centralized Management settingsTo enable and configur e Snmp logging Configuring Network Snmp SettingsConfiguring User Settings Adding a UserUsers UserEditing User Infformation Deleting UsersBlocking a User To delete a UserConfiguring thhe KVM Switch To configure a KVM switchhConfiguring the Security Settings Server nameAccount Blocking section Performing Addditional Configuration OperationsTo configure the security settings Standard Security Policy High Security PolicyTo upgrade firmware Installing an Sssl CertificateTo install an SSL Certifiicate Upgrading FirmmwareDevice Version Upgrade Click Start Upgrade. The upgrade startsReloading a Restoring Factoory SettingsTo restore factory settinngs To reload aSaving Chang es and Logging Out To save changesTo log off To log onto a remote sessiion Conducting a Remote SessionStarting a Remmote Session EnterLeave Mode as Remote Access ToolbarRemote Session Toolbar Buttons Sharing a Remote SessionButton Description Exclusive Session Setting the Session ProfileDisplaying thhe Toolbar To set the session profiileFull Screen Mode To work in full screen moddeTo verify Remote Presence Solutions information Verifying Remote Presence Solutions InformationChanging the Video Performance Settings To exit full screen modeeTo alter the settings Mode, select Fixed or AdaptiveManually Adjus ting Video Settings Adjusting the VideoAutomatically Adjusting the Video Image Refreshing the Video ImageTo manually adjust the video settings Offset, Phase and Scale sectionMedium, and High Managing Keeyboard SequencesAdding a Keybooard Sequence To add a keyboard sequuenceSpecial Key Manager Recording a Ne w Custom Key Editing a Key SequenceDeleting Key Sequuences Synchronizing Mouse PointersTo delete a keyboard sequence Manually Synchhronizing the Mouse To manually synchronizze mouse pointersUSB Option ExamplesAligning the Mouse Pointers Advanced Mouse EmullationDisconnecting the Remote Session Switching to a Different ServerCalibrating Mousee Pointers Troubleshooting Safe Mode Entering Safe ModeRestoring Facttory Defaults To enter Safe modeTo restore device firmw are To restore factory defauultsRestoring the Device Firmware Upgrade Succeeded Using the Keeyboard Hotkeys Operating the Smart 108/116 IP Switching Sysstem LocallyUsing the Ossd Selecting a Computer Configuring the OSD SettingsNavigating the Ossd To select a computerTo configure the OSD settings Configuring thee General SettingsTo configure the generaal settings To activate password proteection Configuring Security Setttings Administrator Status a w ho can  Supervisor Status S who canActivating Autoskip Editing the Switch NammeChanging the OSD Hotkey Serial PortTo configure the ports setttings Configuring the Ports SettingsRestoring OSD to Factoryy Defaults F7 Editing the Computer NammeTo modify the keyboard settings Configuring thee Time SettingsModifying the Keyboard Setting To configure the time s ettingsTo configure the users settings Configuring the U sers SettingsSetting the Scan, Label, and Timeout Period To set the above periodsConfiguring thee Security Settings To give each user the desired access levelOSD Functions F To change a user name or passwordTo view the available OSD functions Scanning Computers F4 Tuning F5Moving the Label F6 Inputting and Updating DDC Information F10 Upgrading the Smart 108/116 IP FirmwareDownloading Upddate Software and Latest Firmware To input the DDC informatiionConnecting the Smart 108/116 IP System Update Software System RequirementsConnecting the RS232 Download Cable Starting and Configuring the Update Software Installing the SoftwareTo install the Update softwware Smart 108/116 IP Switch Update Window Button/Box FunctionTo verify the Smart 108/1166 IP Switch version Smart 108/116 IP Switch VersionVerifying the Verssion Numbers RICC/ROC Version To update the firmwareObtaining New Firmware Updating the FirmwareTo manually update the RICC/ROCs Manually Updating the RICC/ROCsPress Options Advannced Manual Update Troubleshoooting Update SoftwareCommunicationn Error Message To fix the communicatioon problemSmart 108/116 IP Specification Description Technical SpecificationsSpecification 65 x 25 x 25 mm / 2.55 x 0.98 x 0.98 Video Resolution and Refresh Rates Hz →Snmp Events Table Event Text Code CommentConfusereventloginnotsucceededwrongusernameo 201204198 933207EN
Top Page Image Contents