Multi-Tech Systems FR111 owner manual FCC Regulations for Telephone Line Intercon- nection

Page 16

1.4FCC Regulations for Telephone Line Intercon- nection

1.This equipment complies with Part 68 of the FCC rules. On the outside surface of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN). If requested, this information must be provided to the telephone company.

2.As indicated below the suitable jack (USOC connecting arrange- ment) for this equipment is shown. If applicable, the facility interface codes (FIC) and service order codes (SOC) are shown.

3.The ringer equivalence number (REN) is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to the line, as determined by the total RENs, contact the telephone company to determine the maximum REN for the calling area.

4.If this equipment causes harm to the telephone network, the tele- phone company will notify you in advance. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

5.The telephone company may make changes in its facilities, equip- ment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide ad- vance notice in order for you to make necessary modifications in order to maintain uninterrupted service.

6.If trouble is experienced with this equipment (the model of which is indicated below) please contact Multi-Tech Systems, Inc. at the address shown below for details of how to have repairs made. If the trouble is causing harm to the telephone network, the telephone company may request you remove the equipment from the network until the problem is resolved.

7.No repairs are to be made by you. Repairs are to be made only by Multi-Tech Systems or its licensees. Unauthorized repairs void registra- tion and warranty.

8.This equipment cannot be used on public coin service provided by the telephone company. Connection to Party Line Service is subject to state tariffs. (Contact the state public utility commission, public service

16

Image 16
Contents Model FR111 Page Page Trademarks Contents Appendices Ascii Terminal Menu SystemIntroduction and Description Page Introduction MultiFRAD 100-SeriesSetup Software Loading and ConfigurationAbout This Manual Introduction and DescriptionService, Warranty and Tech Support Ascii Terminal Menu SystemTypical Application Ordering a Frame Relay LineHow to Configure a MultiFRAD Page Page FCC Regulations for Telephone Line Intercon- nection Page Canadian Limitations Notice Specifications Data Port TrunkElectrical/Physical/Environmental CompatibilityPage Front and Back Panel Descriptions Page Front Panel DataTrunk Power Connector Trunk ConnectorData Connector Back PanelSwitch Settings DIP-SwitchesShunts ShuntsPage Setup Page Unpacking Safety Warnings DIP-Switch Settings Power Data V.35 Shunt ShuntsSoftware Loading Configuration Page Loading Software Page Page Configuring Your MultiFRAD using Windows Page Page Page Configuring your MultiFRAD using a Dumb Terminal NRZ C e s s r a t e 0 0 Enter Number, or P Previous Menu Page Selection Page Software Utility Descriptions Page MultiFRAD Main Menu Configuration Data Port DiagnosticsOthers Statistics DownloadHelp MultiFRAD VersionData Port Configuration Mode Asynchronous/SynchronousSync Mode Parameters SpeedBetween Frames InterFrame Timer in mSEncoding Scheme CRC Preset Async Mode ParametersBaud Rate Word LengthParity Stop BitsFlow Control PacingEcho Pass XonEIA Pass Through ENQ/ACK Data Link Connection Identifier Dlci Trunk ConfigurationManagement Type Encapsulation Type Management Parameters Polling IntervalError Threshold Full Status CounterMonitored Event Committed Info Rate CIRBack to Back Excess Burst Rate BeStatistics Loop Tests Other TestsPage Ascii Terminal Menu System Page Configurations Menu Async Data Port Configuration CTSChannel Device Trunk Facility Sync Data Port Configuration NRZPage C e s s r a t e 0 0 Page Page Statistics View Statistics Page Reset Options Diagnostic TestsPage Flash Firmware Upgrade Memory TestWatch Dog Test Product and Firmware IDService, Warranty and Tech Support Page Limited Warranty Tech SupportRecording MultiFRAD Information Model Number Serial Number Firmware VersionService About the Multi-Tech BBSLogging on to the Multi-Tech BBS Downloading a FileAbout CompuServe If you don’t know the file nameAbout the Multi-Tech Fax-Back Service About the InternetUsing FlashPro to Upgrade MultiFRAD Firmware Upgrading the Flash PromPage Appendices Page Appendix a Cabling Diagrams Data connector RS232C/V.24 * CableTrunk Cable Pin IdentificationBack-To-Back Cable