Multi-Tech Systems FR111 owner manual

Page 2

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced raido/TV technician for help.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

The CE mark is affixed to the enclosed MultiTech product to confirm compliance with the following European Community Directives:

Council Directive 89/336/EEC of 3 May 1989 on the approximation of the laws of Member States relating to electromagnetic compatibility;

and

Council Directive 73/23/EEC of 19 February 1973 on the harmonization of the laws of Member States relating to electrical equipment designed for use within certain voltage limits;

both amended by

Council Directive 93/68/EEC of 22 July 1993 on the harmonization of CE marking requirements.

Image 2
Contents Model FR111 Page Page Trademarks Contents Appendices Ascii Terminal Menu SystemIntroduction and Description Page Introduction MultiFRAD 100-SeriesAbout This Manual SetupSoftware Loading and Configuration Introduction and DescriptionService, Warranty and Tech Support Ascii Terminal Menu SystemTypical Application Ordering a Frame Relay LineHow to Configure a MultiFRAD Page Page FCC Regulations for Telephone Line Intercon- nection Page Canadian Limitations Notice Electrical/Physical/Environmental Specifications Data PortTrunk CompatibilityPage Front and Back Panel Descriptions Page Front Panel DataTrunk Data Connector Power ConnectorTrunk Connector Back PanelSwitch Settings DIP-SwitchesShunts ShuntsPage Setup Page Unpacking Safety Warnings DIP-Switch Settings Power Data V.35 Shunt ShuntsSoftware Loading Configuration Page Loading Software Page Page Configuring Your MultiFRAD using Windows Page Page Page Configuring your MultiFRAD using a Dumb Terminal NRZ C e s s r a t e 0 0 Enter Number, or P Previous Menu Page Selection Page Software Utility Descriptions Page MultiFRAD Main Menu Others Statistics Configuration Data PortDiagnostics DownloadHelp MultiFRAD VersionSync Mode Parameters Data Port ConfigurationMode Asynchronous/Synchronous SpeedEncoding Scheme InterFrame Timer in mSBetween Frames Baud Rate CRC PresetAsync Mode Parameters Word LengthFlow Control ParityStop Bits PacingEIA Pass Through Pass XonEcho ENQ/ACK Management Type Trunk ConfigurationData Link Connection Identifier Dlci Encapsulation Type Management Parameters Polling IntervalMonitored Event Error ThresholdFull Status Counter Committed Info Rate CIRBack to Back Excess Burst Rate BeStatistics Loop Tests Other TestsPage Ascii Terminal Menu System Page Configurations Menu Async Data Port Configuration CTSChannel Device Trunk Facility Sync Data Port Configuration NRZPage C e s s r a t e 0 0 Page Page Statistics View Statistics Page Reset Options Diagnostic TestsPage Watch Dog Test Flash Firmware UpgradeMemory Test Product and Firmware IDService, Warranty and Tech Support Page Limited Warranty Tech SupportRecording MultiFRAD Information Model Number Serial Number Firmware VersionService About the Multi-Tech BBSLogging on to the Multi-Tech BBS Downloading a FileAbout CompuServe If you don’t know the file nameAbout the Multi-Tech Fax-Back Service About the InternetUsing FlashPro to Upgrade MultiFRAD Firmware Upgrading the Flash PromPage Appendices Page Appendix a Cabling Diagrams Data connector RS232C/V.24 * CableTrunk Cable Pin IdentificationBack-To-Back Cable