Multi-Tech Systems FR111 owner manual Configuring your MultiFRAD using a Dumb Terminal

Page 44

4.4Configuring your MultiFRAD using a Dumb Terminal

To configure your MultiFRAD, power up a terminal or pc running communications software and hit the ENTER key. The Main menu appears on your screen, configure the data port for sync or async mode of operation and the trunk for the frame relay parameters. The Multi- FRAD configuration is contained in the following procedure.

1Apply power to your terminal or pc. After the terminal or pc boots up, run the communications software. Setup your communica- tions software for a speed between 2400 and 115.2K bps, 8-bits, no parity, and 1-stop bit. Press the ENTER key to display the MultiFRAD Main Menu.

2Enter option 1 and press the ENTER key to display the Configura- tion menu.

Configurations

1- Data Port Configuration

2- Trunk Configuration

3- Factory Default Configuration Options S - Store All Configurations

M - Main Menu

P - Previous Menu Selection: _

3If your Data port is being setup for Async mode of operation, proceed to step 4 to configure your data port.

If your Data port is being setup for a sync mode of operation, enter option 1 in the Configuration menu and press ENTER. Enter 1 again and the Data Port Async/Sync submenu is displayed. Enter option 2 for Sync mode of operation. Then proceed to step 5 to configure your data port.

44

Image 44

Contents Model FR111 Page Page Trademarks Contents Appendices Ascii Terminal Menu SystemIntroduction and Description Page Introduction MultiFRAD 100-SeriesSetup Software Loading and ConfigurationAbout This Manual Introduction and DescriptionService, Warranty and Tech Support Ascii Terminal Menu SystemTypical Application Ordering a Frame Relay LineHow to Configure a MultiFRAD Page Page FCC Regulations for Telephone Line Intercon- nection Page Canadian Limitations Notice Specifications Data Port TrunkElectrical/Physical/Environmental CompatibilityPage Front and Back Panel Descriptions Page Front Panel DataTrunk Power Connector Trunk ConnectorData Connector Back PanelSwitch Settings DIP-SwitchesShunts ShuntsPage Setup Page Unpacking Safety Warnings DIP-Switch Settings Power Data V.35 Shunt ShuntsSoftware Loading Configuration Page Loading Software Page Page Configuring Your MultiFRAD using Windows Page Page Page Configuring your MultiFRAD using a Dumb Terminal NRZ C e s s r a t e 0 0 Enter Number, or P Previous Menu Page Selection Page Software Utility Descriptions Page MultiFRAD Main Menu Configuration Data Port DiagnosticsOthers Statistics DownloadHelp MultiFRAD VersionData Port Configuration Mode Asynchronous/SynchronousSync Mode Parameters SpeedEncoding Scheme InterFrame Timer in mSBetween Frames CRC Preset Async Mode ParametersBaud Rate Word LengthParity Stop BitsFlow Control PacingEIA Pass Through Pass XonEcho ENQ/ACK Management Type Trunk ConfigurationData Link Connection Identifier Dlci Encapsulation Type Management Parameters Polling IntervalError Threshold Full Status CounterMonitored Event Committed Info Rate CIRBack to Back Excess Burst Rate BeStatistics Loop Tests Other TestsPage Ascii Terminal Menu System Page Configurations Menu Async Data Port Configuration CTSChannel Device Trunk Facility Sync Data Port Configuration NRZPage C e s s r a t e 0 0 Page Page Statistics View Statistics Page Reset Options Diagnostic TestsPage Flash Firmware Upgrade Memory TestWatch Dog Test Product and Firmware IDService, Warranty and Tech Support Page Limited Warranty Tech SupportRecording MultiFRAD Information Model Number Serial Number Firmware VersionService About the Multi-Tech BBSLogging on to the Multi-Tech BBS Downloading a FileAbout CompuServe If you don’t know the file nameAbout the Multi-Tech Fax-Back Service About the InternetUsing FlashPro to Upgrade MultiFRAD Firmware Upgrading the Flash PromPage Appendices Page Appendix a Cabling Diagrams Data connector RS232C/V.24 * CableTrunk Cable Pin IdentificationBack-To-Back Cable