Linear RE-1 manual Control Wiring, Door or Pedestrian Gate Control

CONTROL WIRING

Gate Control

1.Route two wires between the gate and the RE-1. Connect the gate operator’s OPEN terminals to the RE-1 Relay #1 COM & N.O. terminals.

✦NOTE: For operator wiring specifics, refer to the gate operator’s wiring diagram.

2.If an access keyswitch is required refer to the Optional Keyswitch section of this manual for details on keyswitch wiring and installation.

3.If an external timer for preventing access at certain times is required, route two wires from the RE-1 to the timer contacts. Connect the timer contacts to the RE-1 SENSE #1 and COMMON terminals.

✦NOTE: If the sense input is going to be used as an inhibit input, it must be programmed to select that input type. See programming PPN #29.

GATE OPERATOR (BEHIND GATE)

4 WIRES FOR

RE-1TELEPHONE

ENTRY

SYSTEM

NOTE: ROUTE TELEPHONE

WIRES AWAY FROM POWER

WIRES

2 WIRES FROM RE-1	2 WIRES FROM
TO GATE OPEN TERMINALS	TRANSFORMER
	FOR RE-1 POWER

Figure 11. Gate Installation Example

Door or Pedestrian Gate Control

1.Install a low voltage electric door strike or magnetic lock as a locking device for the door or pedestrian gate.

2.Install the power supply or transformer for the locking device. DO NOT

POWER THE RE-1 FROM THIS POWER SUPPLY.

3.Connect one wire from the power supply to one wire from the locking device.

4.Route two wires between the locking device and the RE-1. Connect one wire to the remaining wire of the locking device. Connect the other wire to the remaining wire of the power supply.

•For a door strike, connect the wires to the RE-1 Relay #1 COM & N.O. terminals.

•For a magnetic lock, connect the wires to the RE-1 Relay #1 COM & N.C. terminals.

5.If an access keyswitch is required refer to the Optional Keyswitch section of this manual for details on keyswitch wiring and installation.

6.To use the door sense feature to detect forced entry or door ajar conditions, install a normally closed door switch on the door or pedestrian gate and route two wires from the switch to the RE-1. Connect the door sense switch to the RE-1 SENSE #1 and COMMON terminals. See programming PPN #24 & #27 to defi ne when Relay #2 will activate based on the sense input.

2 WIRES	4 WIRES FOR
FOR DOOR	TELEPHONE
SENSE	NOTE: ROUTE TELEPHONE
SWITCH
	WIRES AWAY FROM
DOOR	POWER WIRES
SENSE
SWITCH
	RE-1
ELECTRIC	ENTRY
DOOR	SYSTEM
STRIKE
	2 WIRES FOR RE-1
	POWER FROM
2 WIRES	TRANSFORMER
FOR DOOR
STRIKE
	2 WIRES FOR DOOR
	STRIKE POWER FROM
	POWER SUPPLY

Figure 13. Door Installation Example

	RELAY				RELAY
	#1				#2
N.O.		COM	N.C.	N.O.	COM	N.C.

RE-1

TERMINALS

GATE

OPEN OPERATOR

	RELAY			RELAY
	#1			#2
N.O.	COM	N.C.	N.O.	COM	N.C.

ELECTRIC

DOOR STRIKE

RE-1

TERMINALS

TRANSFORMER TRANSFORMER BATTERY NEGATIVE BATTERY POSITIVE SENSE #1 OPEN #1 SENSE #2 OPEN #2

COMMON

KEYPAD CLK

KEYPAD DVAL

KEYPAD DAT 0

KEYPAD DAT 1

KEYPAD GND

KEYPAD PWR

REQUIRED WIRING

OPTIONAL WIRING

NOTE: IN THIS EXAMPLE SENSE #1 TERMINAL IS SET AS AN INHIBIT INPUT

INHIBIT

TIMER

ACCESS

KEYSWITCH

TRANSFORMER TRANSFORMER BATTERY NEGATIVE BATTERY POSITIVE SENSE #1 OPEN #1 SENSE #2 OPEN #2

COMMON

KEYPAD CLK

KEYPAD DVAL

KEYPAD DAT 0

KEYPAD DAT 1

KEYPAD GND

KEYPAD PWR

REQUIRED WIRING

OPTIONAL WIRING

DOOR STRIKE

POWER SUPPLY

DOOR

SENSE

SWITCH

ACCESS

KEYSWITCH

Figure 12. Gate Installation Wiring

Figure 14. Door Installation Wiring

8