Installation Information

Before beginning installation, please review the entire instructions and become familiar with the system’s operation, wiring, and programmable options.

System Location

For pedestrian door or gate installations, mount the Entry System on a rigid wall near the controlled door. Avoid mounting the unit in a location where regular mechanical shock will occur due to a slamming door or spring loaded pedestrian gate.

For vehicular gate installations, mount the Entry System in clear view of the gate, but far enough from the gate so the user cannot touch the gate from the keypad.

★WARNING FOR ALL GATE INSTALLATIONS:TO AVOID SERIOUS INJURY OR DEATH, MAKE SURE THAT THE UNIT IS FAR ENOUGH FROM THE GATE SO THAT THE USER CANNOT TOUCH THE GATE WHILE OPERATING THE KEYPAD. HOWEVER, FOR SAFETY, THE GATE MUST BE FULLY VISIBLE FROM THE KEYPAD.

RFI Filter Installation

An in-line ferrite RFI ﬁ lter has been included with this unit to install during the wiring of the RE-1 Residential Telephone Entry System.

✦NOTE: To insure FCC Part 15 Class B compliance, the following steps must be performed at the time the RE-1 is installed.

1.Open the ferrite RFI ﬁ lter case by gently pulling on the side locking tab and swinging the case open (see Figure 1).

★CAUTION: The ferrite parts of the RFI ﬁlter are fragile.

DO NOT DROP THE FILTER ON A HARD SURFACE! Damage to the ﬁlter may result.

2.After completing the RE-1 installation, route all wires except the AC transformer and telephone lines through the grove in the ferrite core of the RFI ﬁ lter. The ﬁ lter must be installed outside of the RE-1 case. With the wires captured inside, close the ferrite RFI ﬁ lter case and snap it shut (see Figure 1).

✦NOTE: Be sure the ﬁlter is located no further than two inches from the rear case cover of the RE-1.

NOTE: INSTALLATION OF THE RFI FILTER WILL

INSURE MAXIMUM RADIO RECEPTION RANGE

FOR ACCESS TRANSMITTERS

	RFI FILTER
PULL ON PLASTIC TAB	INSTALLED
PULL ON PLASTIC TAB	WITHIN 2"
TO UNLOCK FILTER CASE	OF RE-1 CASE

SWING FILTER

CASE OPEN

PHONE AND

TRANSFORMER WIRES

OUTSIDE OF FILTER

FERRITE

CORE

Figure 1. RFI Filter Installation

Telephone Wires

The quality of the system’s audio communications is related to the type of telephone wire and its installation. Noise and hum can be introduced into the telephone wires. Use only high-quality telephone wire rated for direct underground burial. All telephone wire should be twisted-pair.

•Minimum size of 24 AWG for up to 800 feet.

•Minimum size of 22 AWG for up to 1600 feet.

•Minimum size of 20 AWG for up to 2200 feet.

•Minimum size of 18 AWG for up to 3600 feet.

DO NOT ROUTE TELEPHONE AND AC WIRING INSIDE THE SAME CONDUIT. Route all telephone wires inside a dedicated conduit that is at least six inches away from any AC line wiring.

Power Supply

Use the supplied 16-volt 20-VA transformer to power the RE-1.

DO NOT POWER ANY OTHER EQUIPMENT FROM THE SAME TRANSFORMER, use a separate power supply. Keep the system power wires as short as practical to reduce the chance of noise and hum pickup.

•For low voltage power wire runs up to 100 feet, use 18 AWG, THHN 600-volt insulated wire.

•For low voltage power wire runs up to 200 feet, use 16 AWG, THHN 600-volt insulated wire.

•Use 22 AWG or larger (depending on the load) for all other connections.

ALWAYS REMOVE POWER PRIOR TO SERVICING

Earth Ground

To avoid damage to the unit from static discharges, connect the RE-1’s EARTH GROUND and case ground terminals to a good earth grounding point within 10 feet. The case ground terminal is the #8 screw located on the backplate above the wire entry hole. Also, the RE-1’s Telephone Bypass Module must be grounded to provide surge protection for the telephone line. Suggested wiring size is 12 AWG for earth ground.

Removable Terminal Strips

For convenience, the RE-1 is provided with removable terminal strips. It is important that these strips be removed evenly in order to avoid causing permanent damage to them.

1.Be certain power is off before removing or installing these strips.

2.With a small screwdriver, gently slide the blade between the terminal strip and protective label.

3.Slightly pry ﬁ rst one end, then the other, and then the middle. Repeat the process until the terminal strip can be removed straight off the circuit board by hand. Be very careful to not damage circuit board traces.

4.When re-installing the terminal strips, press down straight and evenly.

Do not remove or install one end ﬁ rst.This will bend pins on the circuit board, which will damage the terminal strip internally. This damage is permanent and can not be repaired by simply straightening the pins on the circuit board.

✦NOTE: Unscrew the terminal screws several turns before inserting wires.