Linear RE-1 manual Linear Limited Warranty, Important Wireless Information

Page 32

LINEAR LIMITED WARRANTY

This Linear product is warranted against defects in material and workmanship for twenty-four (24) months. The Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear LLC for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for fi tness, are valid only until Warranty Expiration Date as labeled on the product. This

Linear LLC Warranty is in lieu of all other warranties express or implied.

All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.

IMPORTANT WIRELESS INFORMATION

Linear radio controls provide a reliable communications link and fi ll an important need in portable wireless signaling. However, there are some limitations which must be observed.

For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range.

A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings.

Changes or modifi cations to the device may void FCC compliance.

Infrequently used radio links should be tested regularly to protect against undetected interference or fault.

A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users.

FCC NOTICE

Changes or modifi cations not expressly described in this manual or approved by the manufacturer could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Copyright © 2008 Linear LLC

217490 C

Image 32
Contents RE-1 Contents FeaturesAccess Media System FeaturesProduct Description OperationInstallation Information Component Locations KeypadWiring Diagram Typical Gate Installation WiringTelephone Wiring Entry System MountingTelephone Wiring Options Intercom ModeRing Down Mode Shared LineShared Line Mode Multiple Unit InstallationsCommand Prefix for Multiple Units Door or Pedestrian Gate Control Control WiringGate Control POWER, BATTERY, & Ground Wiring Power WiringBackup Battery Optional Remote KeypadOptional Keyswitch Keyswitch InstallationCamera Installation Optional Cctv CameraSystem Requirements Programming AccessProgramming with a Computer NEW Connection Wizard will Start Click Next Select Networking TABClick Dial RE-1 willFill in the Information for the Connection Choose SET UP a DIAL-UP ConnectionFrom the Start MENU, Click on Connect to Click on USE the Following IP Address and Enter Click on CloseConnect WINDOW, Select Properties Connecting to the RE-1 with Windows Vista Click on Dial Start the ConnectionLocal Programming Access Remote Programming AccessProgramming with a Local Telephone or the Unit’s Keypad Remote Programming with a TelephoneProgramming Reference Programming ControlBasic System Programming Entry Code ProgrammingTransmitter Programming Telephone ProgrammingAdvanced System Programming Model MGT Gate Edge Transmitter Setup Relay #2 Alternate OptionsRemote Keypad Address Sense Input Alternate FunctionDigital Speech Volume System AdjustmentsSpeakerphone Volume RE-1 Operation To Enter Programming Mode To Exit Programming Mode & Save ChangesRe-entering a Command After a Mistake Call Waiting Feature On/OffTroubleshooting SpecificationsDimension Drawing Programming Worksheet Time ZonesEntry Code Relay # Time Zone Linear Limited Warranty Important Wireless Information