System Adjustments, Speakerphone Volume

Keypad Beeps On/Off

Default: On

The default setting causes the main keypad to beep when each key is pressed. The beeps can be disabled.

Press: Keypad Beeps

Keypad Beeps: 0 = Beeps OFF

1 = Beeps ON

Relay #1 Tone On/Off

Default: Off

The default setting does not cause the annunciator to sound when Relay #1 is activated. The Relay #1 activation tone can be enabled.

Press: Relay #1 Tone

Relay #1 Tone: 0 = Tone OFF

1 = Tone ON

Relay #2 Tone On/Off

Default: Off

The default setting does not cause the annunciator to sound when Relay #2 is activated. The Relay #2 activation tone can be enabled.

Press: Relay #2 Tone

Relay #2 Tone: 0 = Tone OFF

1 = Tone ON

Relay Tone Duration

Default: 1 Second

The default setting causes the annunciator to sound for 1 second when Relay #1 or Relay #2 is activated (if the tones are enabled). The length of the activation annunciation can be changed.

Press: Tone Length

Tone Length = Tone length in Seconds 1-15

Voice Synthesizer On/Off

Default: On

When the voice synthesizer is on the RE-1 will sound voice prompts during operation and programming. If the voice synthesizer is off, the system will sound beeps to indicate conditions. The HELP button will announce “Enter code or press call button to contact resident” regardless of this setting.

The beeps produced when the voice synthesizer is off are:

•1 Short beep — Keypad key pressed

•2 Short beeps — Programming entry was valid

•1 Long beep — Programming entry was invalid

Press: Voice

Voice: 0 = Voice synthesizer OFF 1 = Voice synthesizer ON

Automatic Daylight Saving Time Clock Adjustment On/Off Default: On

The RE-1’s internal clock used for controlling system functions and time stamping of the event log automatically adjusts for daylight saving time. The time will change on the ﬁ rst Sunday in April, and on the last Sunday of October. For areas where daylight saving time is not observed, this feature may be disabled.

Press: Daylight Saving

Daylight Saving: 0 = Daylight Saving Adjust OFF

1 = Daylight Saving Adjust ON

Automatic Door/Gate Open Time

Default: Not Set

Each control relay can be programmed for automatic activation. One or two Time Zones can be assigned to a relay. The relay will activate and remain latched during the active period of the Time Zone.

Press: Relay 1st Time Zone 2nd Time Zone

Relay: 1 = Relay #1 2 = Relay #2

1st Time Zone = Time Zone 1-7

2nd Time Zone = Time Zone 1-7 (enter “0” if the 2nd time zone is not used)

SYSTEM ADJUSTMENTS

The RE-1 Entry System audio levels can be adjusted to suit the installation requirements. If required, make these adjustments after programming, but before closing and securing the RE-1 case.

Speakerphone Volume

The SPEAKERPHONE VOLUME adjustment controls the audio level that the RE-1 speaker produces during communications between the visitor and the resident.

✦NOTE: Adjusting the speaker volume too high will cause the speech to cut-out as the system switches from talk to listen.

1.Have someone waiting to receive the call. Push the CALL button to call the residence.

2.Have the resident talk at a normal volume level while adjusting the SPEAKERPHONE VOLUME control. Adjusting the control clockwise increases the volume, counterclockwise decreases the volume.

Digital Speech Volume

The DIGITAL SPEECHVOLUME adjustment controls the audio level of the voice synthesizer. This adjustment effects the audio level of the voice synthesizer from the speaker and through the telephone.

1.Push the HELP button to cause the voice synthesizer to sound the help message.

2.Adjust the DIGITAL SPEECH VOLUME to suit the installation. Adjusting the control clockwise increases the volume, counterclockwise decreases the volume.