LevelOne FPS-2101USB manual LED Indicators, DIP Switches FPS-2101TXU & FPS-2003TXU, Description

Page 14

Introduction

LED Indicators

All LevelOne Printer Servers are fitted with 2 LED indicators. The red LED is the Status/Error indicator. The green LED is the Power/Link indicator. The LED indicator modes are described in the following table.

Green LED

Red/Orange LED

Status Description

Off

Off

No power.

 

 

 

On

On

Hardware error.

 

 

 

Flashing

Flashing

Firmware upgrade in progress.

 

 

 

On

Flashing (USB only)

No printer connected to the USB port.

 

 

 

On

Off

Normal operation - idle.

 

 

 

Flashing

Off

Normal operation - transmitting or

 

 

receiving packets from the network.

 

 

 

DIP Switches - FPS-2101TXU & FPS-2003TXU

The DIP switches are used to set the LAN connection. Operation is as follows.

SW1

SW2

SW3

Description

UP

UP

UP

Auto select LAN connection (Default)

 

 

 

 

UP

UP

Down

Use BNC connector

 

 

 

 

Down

Down

Down

10BaseT - Half Duplex

 

 

 

 

Down

Down

UP

10BaseT - Full Duplex

 

 

 

 

Down

UP

Down

100BaseT - Half Duplex

 

 

 

 

Down

UP

UP

100BaseT - Full Duplex

 

 

 

 

The other possibilities are reserved, and should not be used.

DIP Switches - FPS-2111TXU & FPS-2013TXU

The DIP switches are used to set the LAN connection. Operation is as follows.

SW1

SW2

SW3

Description

UP

-

-

Auto select LAN connection (Default)

 

 

 

Switches 2 and 3 have no effect.

Down

Down

Down

10BaseT - Half Duplex

 

 

 

 

Down

Down

UP

10BaseT - Full Duplex

 

 

 

 

Down

UP

Down

100BaseT - Half Duplex

 

 

 

 

Down

UP

UP

100BaseT - Full Duplex

 

 

 

 

The other possibilities are reserved, and should not be used.

- 11 -

Image 14
Contents Level One Printer Servers Table of Contents Specifications Special FeaturesTroubleshooting Windows NT Server TCP/IPYear 2000 Compliance FeaturesIntroduction Safety Instructions Package Contents Description ModelsEPS-3001TU 10BaseT Direct Attach FPS-3001TXU 100BaseT Direct Attach Item DescriptionFPS-2111TXU FPS-2101TXU FPS-2013TXU FPS-2003TXU FPS-2101USB DIP Switches FPS-2111TXU & FPS-2013TXU LED IndicatorsDIP Switches FPS-2101TXU & FPS-2003TXU Green LED Red/Orange LED Status DescriptionTo generate a Diagnostic print out Diagnostic Push ButtonTo restore the factory default settings Find the Default LevelOne Printer Server Name LAN InstallationProcedure Connect the PrintersPower Up and Check Configuration Methods & Utilities ConfigurationRequired Configuration WebAdmin WPConfigRequirements BiAdmin Utility ProgramInstallation Additional RecommendationsBiAdmin Main Screen Main ScreenGroups Device ListConfiguration Icons Status IconsOther Icons InitDevice Menu Menu OptionsStatus Menu Control Menu Configuration MenuDiagnostics menu Software Requirements AppleTalk SetupAppleTalk PrintingWindows Software Advanced Setup and ManagementChanging the Device Configuration Macintosh SoftwareApple Zone AppleTalk SettingsDevice Name APPCOMM1 No APPCOMM2 No APPCOMM4 NoNetWare Configuring NetWareConfiguring the LevelOne Printer Server OverviewConfiguration Methods Using BiAdmin with Client PreparationButtons Print Server Mode BinderyData If you have multiple File Servers NetWare Configuration Button BinderyQuickset Button Bindery If you have a single File Server Printer Button Select Printer Port BinderyAssigning Printer Queues Required Assign Queues BinderyTo Assign Users to Queues Required To assign operators to Queues OptionalPassword NetWare Password Bindery PS ModePrint Server Mode NDS NetWare Configuration Button NDS Quickset Button NDSSelect Printer Port NDS Assign Users to Queue NDS PS mode To assign operators to the Print Queue OptionalPassword NDS NetWare Password NDS PS ModeRemote Printer Mode Bindery Remote Printer Mode NDS Current ContextCreating an Ndps Manager Object Ndps NetWareOverview Creating an Ndps Printer Agent Load NdpsmWorkstation Configuration ProcedureNdps Manager Client Example Windows Web Browser ConfigurationExample Unix Connecting to the LevelOne Printer Server TCP/IP Configuration Data TCP/IP ScreenOther Screens Logical Printer ConfigurationLogical Printer Setup Data String Before JobTelnet OperationUnix IP Address ConfigurationProcedure Software RequirementsPrinting Methods Overview Using BootpUsing Rarp Direct Socket InterfaceFTP File Transfer Protocol LPD Printing ConfigurationLPD on IBM AIX Adding Remote Printers Action Sample CommandLPD on System LPD on BSD Printing using LPD Other Printing Methods Printing Using DSIPrinting Using PSfilter Logical Printer No Socket NoLevelOne Printer Server Configuration Windows NT Server TCP/IPWindows NT Host Configuration Host File Entry OptionalWindows NT Preparing for TCP/IP PrintingAdding a TCP/IP Remote Printer WindowsWindows NT Server TCP/IP Windows Applications Command LinePrinting with Windows NT Setup Windows Peer-to-PeerIf your LevelOne Printer Server is not listed Add Port Peer-to-peer Print DriverConfigure Printer Port ManagementRetry Interval Port OptionsBanner System Requirements Special FeaturesInternet Printing Mail ServerInternet Printer Server User Client RequirementsUser Software Internet Mail Printing ConfigurationInstallation User Software Following data must be provided Using the new Port Checking the Printer DriverCanceling a Print Job Printing through the InternetManagement Station Settings Configuring the LevelOne Printer Server for SnmpSnmp Settings Trap Receiving Station SettingsTrap Severity Problem No All the LevelOne Printer Server’s LEDs are off TroubleshootingHardware Problems Printing General Problem NoBiAdmin is grayed out, even though my printer in bi DirectionalProblem No My file doesn’t print with the correct fonts Problem No Why do I get an incorrect printout?Problem No My document didn’t print to the right printer Problem No My EPS file doesn’t print with the correct fontsLevel One Printer Servers NetWare 2.x Problem No My LevelOne Printer Server prints garbageNetWare NetWare 4.x bindery and NDS modesSet Allow service by current print servers to YES Troubleshooting Then select Print Server Configuration and select Queues Problem No PSConfig shows No ResponseCannot receive Notify message in NetWare 4.x environment Problem No LevelOne Printer Server device is not recognized TCP/IP Unix & Windows NTProblem No I can’t print using LPD Problem No I can’t print using PSfilterTo remove an existing printer port installation Windows Peer-to-peerTroubleshooting Then select File Properties Details Problem No a print job is printing garbage Problem No I don’t know my Mail Server’s IP AddressProblem No Plain text E Mails are not printed Problem No Two print jobs are printing on the sameProblem No Only the banner page was printed Select Properties DetailsEPS-3001TU SpecificationsDirect Attach Models FCC StatementFPS-3001TXU Environmental Specifications Parallel Port Pin AssignmentsOther Models Strobe To printer +Data Level One Printer Servers

FPS-2111TXU, FPS-2101TXU, FPS-2003TXU, FPS-2013TXU, FPS-2101USB specifications

LevelOne has established itself as a reputable brand that offers a diverse range of high-quality networking products. Among its impressive catalog, the devices EPS-3001TU, FPS-2003TXU, FPS-2101USB, FPS-2101TXU, and FPS-2111TXU stand out for their unique features and capabilities tailored to meet various networking needs.

The LevelOne EPS-3001TU is an advanced PoE (Power over Ethernet) injector that enhances network efficiency by transmitting both power and data through a single cable. This device supports IEEE 802.3af PoE standards, making it compatible with a wide array of PoE-enabled devices such as IP cameras and wireless access points. With a compact design, the EPS-3001TU is easy to install and ideal for environments where space is a concern. Its LED indicators provide real-time feedback on power and data transmission, ensuring reliable performance at all times.

The FPS-2003TXU is a robust network switch designed to facilitate seamless data flow in various applications. Featuring 3 Gigabit Ethernet ports, it offers a high-speed data transfer rate that minimizes latency. Plug-and-play functionality allows for effortless integration into existing networks, while its compact and fanless design ensures quiet operation, making it suitable for office environments. The FPS-2003TXU also boasts energy-efficient technology, reducing overall power consumption without compromising performance.

The FPS-2101USB, on the other hand, combines the traditional switch functionality with USB connectivity. This unique feature allows users to easily connect USB devices directly, thereby broadening the scope of network sharing. Ideal for small offices, the FPS-2101USB supports multiple simultaneous connections, enhancing productivity and collaboration among users. The device is designed for simplicity, ensuring easy setup and management.

Similarly, the FPS-2101TXU and FPS-2111TXU are reliable managed switches that offer extensive management features and enhanced security protocols. Both models come with multiple ports for optimal connectivity and support high-definition video and voice traffic. They are equipped with VLAN support, allowing for efficient traffic segmentation and improved network performance. Moreover, their robust security features, including port security and access control lists, ensure that network integrity is maintained.

In conclusion, LevelOne's EPS-3001TU, FPS-2003TXU, FPS-2101USB, FPS-2101TXU, and FPS-2111TXU devices provide a strong foundation for building and managing efficient networks. With a combination of innovative features, user-friendly design, and reliable performance, these products cater to the needs of both home and business environments, ensuring that users get the most out of their networking infrastructure.