Lantronix LX6 manual To Configure Tunnel Serial Settings, Tunnel Packing Mode Settings

Page 30

 

 

6: Line and Tunnel Settings

 

 

Table 6-3 Tunnel Serial Settings

 

 

 

 

Tunnel Serial

Description

 

Settings

 

 

Line Settings

Line Settings information here is display only. Go to the section, To Configure

 

 

Line Settings to modify these settings.

 

 

 

 

Protocol

Protocol information here is display only. Go to the section, To Configure

 

 

Line Settings to modify these settings.

 

 

 

 

DTR

Select the conditions in which the Data Terminal Ready (DTR) control signal

 

 

on the serial line are asserted. Choices are:

 

 

Unasserted

 

 

TruPort = the DTR is asserted whenever either a connect or an accept

 

 

mode tunnel connection is active with the Telnet Protocol RFC2217 saying

 

 

that the remote DSR is asserted.

 

 

Asserted while connected = the DTR is asserted whenever either a

 

 

connect or an accept mode tunnel connection is active.

 

 

Continuously asserted

 

 

 

To Configure Tunnel Serial Settings

Using Web Manager

To configure the Serial Settings for a specific tunnel, click Tunnel in the menu and select Tunnel 1 -> Serial Settings.

Using the CLI

To enter Tunnel 1 command level: enable -> tunnel 1 -> serial

Using XML

Include in your file: <configgroup name=”tunnel serial” instance=”1”>

Packing Mode

With Packing, data from the serial Line is not sent over the network immediately. Instead, data is queued and sent in segments, when either the timeout or byte threshold is reached. Packing applies to both Accept and Connect Modes.

 

Table 6-4 Tunnel Packing Mode Settings

 

 

 

Tunnel Packing Mode

 

Description

Settings

 

 

Mode

 

Configure the Tunnel Packing Mode. Choices are:

 

 

Disable = Data not packed.

 

 

Timeout = data sent after timeout occurs.

 

 

Send Character = data sent when the Send Character is read on the Serial

 

 

Line.

 

 

 

Threshold

 

Set the threshold (byte count). If the received serial data reaches this

 

 

threshold, then the data will be sent on the network. Valid range is 100 to

 

 

1450 bytes. Default is 512.

 

 

 

XPort® Pro Lx6 Embedded Device Server User Guide

30

Image 30
Contents Embedded Device Server User Guide Contacts WarrantyIntellectual Property DisclaimerTable of Contents Configurable Pin Manager Line and Tunnel SettingsTerminal and Host Settings Services SettingsMaintenance and Diagnostics Settings Branding the XPort Pro Lx6 Advanced SettingsUpdating Firmware Appendix a Technical SupportList of Figures XPort Pro Lx6 Product LabelList of Tables XPort Pro Lx6 Embedded Device Server User Guide Summary of Chapters Using This GuidePurpose and Audience Chapter DescriptionAdditional Documentation Document DescriptionKey Features IntroductionApplications Troubleshooting Capabilities Configuration MethodsProtocol Support Hardware Address Addresses and Port NumbersProduct Information Label IP AddressXPort Pro Lx6 Product Label Current Settings Description Using DeviceInstallerAccessing XPort Pro Lx6 Using DeviceInstaller Device Detail SummaryComments Supports Configurable PinsGroup Device FamilyConfiguration Using Web Manager Accessing Web ManagerDevice Status 1Device StatusWeb Manager Components Help AreaNavigating Web Manager Web Manager PagesWeb Manager Description See Network FilesystemLine Protocol StackNetwork Interface Settings Network SettingsNetwork Interface Settings Network Interface Description SettingsTo Configure Network 1 Interface Settings Network 1 Ethernet eth0 Description Link Settings Network Ethernet Network eth0 Link SettingsNetwork 1 eth0 Link Settings To View Network 1 Interface StatusTo Configure Network 1 Link Settings Line Configuration Settings Line and Tunnel SettingsLine Settings Line Settings DescriptionTo Configure Line Settings Line Command Mode SettingsLine Command Description Mode Settings Tunnel Settings Serial SettingsTo View Line Statistics Tunnel Serial Settings To Configure Tunnel Serial SettingsPacking Mode Tunnel Packing Mode SettingsTimeout To Configure Tunnel Packing Mode SettingsAccept Mode Send CharacterTunnel Accept Mode Settings Tunnel Accept Mode Description SettingsTo Configure Tunnel Accept Mode Settings Connect ModeReconnect Timer Tunnel Connect Mode SettingsTunnel Connect Mode Description Settings HostTunnel Disconnect Mode Settings To Configure Tunnel Connect Mode SettingsDisconnect Mode Tunnel Disconnect Description Mode SettingsTunnel Modem Description Emulation Settings To Configure Tunnel Disconnect Mode SettingsTunnel Modem Emulation Settings Modem EmulationTo View Tunnel Statistics To Configure Tunnel Modem Emulation SettingsStatistics Connect StringTerminal and Host Settings Terminal SettingsTerminal on Network and Line Settings To Configure the Terminal Network Connection To Configure the Terminal Line ConnectionCurrent Configurable Pins Configurable Pin ManagerCPM Configurable Pins CP StatusCPM Groups Configurable Pin ManagerCPM Group Current Configuration CPM Group StatusTo Configure CPM Settings To View or Configure DNS Settings Services SettingsDNS Settings DNS SettingsTo Configure FTP Settings FTP SettingsSyslog Settings FTP SettingsHttp Settings Http SettingsTo View or Configure Syslog Settings Severity Log LevelHttp Settings Description To Configure Http SettingsTo Configure Http Authentication Http Authentication Description SettingsUsing the CLI File Display Settings Maintenance and Diagnostics SettingsFilesystem Settings File DisplayFile Modification File Modification SettingsFile Transfer Settings File TransferTo Configure IP Network Stack Settings Protocol Stack SettingsIP Settings Protocol Stack Description IP SettingsTo View ICMPv6 Network Stack Settings Icmp and ICMPv6 SettingsTo Configure Icmp Network Stack Settings ARP SettingsTo Configure Smtp Network Stack Settings To Configure ARP Network Stack SettingsSmtp Settings Default isIP Sockets DiagnosticsHardware To View Hardware Information To View the List of IP SocketsTo Ping a Remote Host Ping SettingsPing TracerouteLog To Configure the Diagnostic Log Output10 Log Settings MemoryTo View Process Information ThreadsProcesses To View Thread Information11 System Settings System SettingsTo Reboot or Restore Factory Defaults 12 CLI Configuration Default Settings15 Tunnel Default Settings 13 Line Configuration Default Settings14 Network Configuration Default Settings 16 Discovery SettingsTo View, Configure and Send Email Advanced SettingsEmail Settings Email Configuration Description SettingsTo View and Configure Basic CLI Settings Command Line Interface SettingsBasic CLI Settings CLI Configuration SettingsTo Configure Telnet Settings XML SettingsTelnet Settings XML Export ConfigurationXML Export Status To Export Configuration in XML FormatXML Exporting Configuration Exporting StatusImport Configuration from Description Filesystem Settings XML Import ConfigurationImport Configuration from Filesystem Settings To Export in XML FormatTo Import Configuration in XML Format Whole Groups to ImportText List Updating Firmware Obtaining Firmware Loading New Firmware through Web ManagerLoading New Firmware through FTP Updating FirmwareBranding the XPort Pro Lx6 Web Manager CustomizationShort and Long Name Settings Short and Long Name CustomizationTo Customize Short or Long Names Europe, Middle East, Africa Emea Appendix a Technical SupportNorth America Japan Asia / Pacific ApacOnline Appendix B Compliance Product Name ModelAppendix B Compliance RoHS NoticeConversion Table Appendix C Binary to Hexadecimal ConversionsConverting Binary to Hexadecimal Scientific CalculatorAppendix C Binary to Hexadecimal Conversions
Related manuals
Manual 87 pages 781 b