Intelligent Motion Systems DSP-402 manual 6060h Mode of Operation, ±Integer8, Modes of Operation

Page 39

SECTION 5

Modes of Operation

Object 6060h — Modes of Operation

The performance of the MDrivePlus CANopen depends on the activated Modes of Operation. It is not possible to operates the modes in parallel. The user must select a mode to operate in. An example of exclusive functions are Profile Velocity and Profile Position modes.

The MDrivePlus allows the user to switch dynamically from operation mode to operation mode.

Mode of Operation

(6060h)

Operation

Mode

Function

Profile Velocity Mode

Profile Position Mode

Homing Mode

Mode of Operation Display

(6061h)

Figure 5.1: Mode of Operation

The IMS MDrivePlus CANopen supports the following Modes of Operation:







Profile Position

Profile Velocity

Homing Mode

Object Description

	Index		Name			Object Code		Data Type
	6060h		Mode of Operation			VAR		±Integer8
Entry Description

		Access		PDO Mapping	Range		Default
		rw		n/a	±Integer8		n/a

Data Description

The actual mode is reflected in the modes_of_operation_display (index 6061h), and not in the modes of operation (index 6060h). It may be changed by writing to modes of operation.

Part 2: DSP-402 Implementation

31

Image 39

Contents Forcetm CANopen DSP402 Application Revision R020507 Contents Device Control Profile Position Mode Optional Application FE General I/O List of Figures This Page Intentionally Left Blank Application Guide MDrivePlus CANopen R020507 Introduction Can Message FormatMDrivePlus Architecture Device Control Homing Mode SectionProfile Position Mode Section Profile Velocity Mode SectionTrajectory Generator Objects and the Object DictionaryYes/No Xxxx h Index NameRange DefaultPDO Mapping CategoryIntentionally Left Blank PDO Attributes Accessing The MDrivePlus CANopenService Data Object SDO Process Data Object PDOPDO Mapping Procedure Consumer PDO Default Mapping Example Consumer PDOPDO Mapping 1600h Object Description Mapping Parameters PDO ObjectsConsumer PDO1 RPDO1 1400h Object Description Consumer PDO1 RPDO1 1400h Entry Description1601h Entry Description Mapping Parameters Consumer PDO2 RPDO2 1401h Object DescriptionConsumer PDO2 RPDO2 1401h Entry Description 1601h Object Description Mapping Parameters1602h Entry Description Mapping Parameters Consumer PDO3 RPDO3 1402h Object DescriptionConsumer PDO3 RPDO3 1402h Entry Description 1602h Object Description Mapping ParametersProducer PDO2 TPDO2 1801h Object Description Producer PDO1 TPDO1 1800h Entry Description1A00h Object Description Mapping Parameters 1A00h Entry Description Mapping ParametersProducer PDO3 TPDO3 1802h Entry Description 1A01h Object Description Mapping Parameters1A01h Entry Description Mapping Parameters Producer PDO3 TPDO3 1802h Object Description1A02h Entry Description Mapping Parameters Unsigned Object 2000h I/O Discretes ConfigAccessibility Codes Discretes2002 h Config Input Switches Object 2002h I/O Discretes ConfigObject 2004h Input Filter Mask Config 2004h 2006h Input Filter TimeObject 2006h Input Filter Time ms Unsigned Hardware 2010h Analog InputSee Entry Desc 2020h Software Limits as2033 h Capture Input 2031 h Unit Options2032 h Clock Options See TableObject 2205h Hold Current Percent 2204 h Run Current %2205 h Hold Current % Object 2204h Run Current PercentPoint Target Options Setting2211h Integer5003h Factory5002h Ascii Ser. NoControl and Status words State MachineState Machine Transitions Internal 6040 h Unsigned16Object 6040h Controlword Object 6041h Statusword StatuswordBit 7 Warning Bit 4 Voltage EnabledBits 12-13 Operation Mode Specific Bit 5 Quick Stop ActiveObject 6060h Modes of Operation 6060h Mode of Operation±Integer8 Modes of Operation6061 h Mode of Operation Display Object 6061h Modes of Operation DisplayObject 6502h Supported Drive Modes = Mode Supported = Mode Not Supported Intentionally Left Blank Input Data Description Profile Position ModeGeneral Information Trajectory GeneratorSet-Point Transmission from Host Computer Functional DescriptionSingle Set-Point Mode Move After a Move 6040h Bit 5=0 Controlword 6040h of Profile Position Mode607A h Target Position Possible Integer6081 h Profile Velocity 6082 h End Velocity 6083 h Profile Acceleration6084 h Profile Deceleration Object 6086h Motion Profile Type 6086 h Motion Profile TypeInternal States Homing ModeInput Data Description Output Data DescriptionStatusword 6041h of Homing Mode 607C h Homing OffsetHoming Offset 607Ch Homing Method 6098h 6098 h Homing Method± Integer Possible ± IntegerMethod 2 Homing on the Positive Limit Switch and Index Pulse Homing on the Negative Home Switch and Index Pulse Methods 7 to 14 Homing on the Home Switch and Index PulseMethods 15 and 16 Reserved Methods 17 to 30 Homing without an Index PulseMethods 31 and 32 Reserved Homing Speeds 6099h 6099 h Homing SpeedsMethods 33 and 34 Homing on an Index Pulse Method 35 Homing on the Current PositionIntentionally Left Blank Position Control Function 6062 h6063 h Position Actual Value 6064 h Position Actual ValueUnsigned Mfg-Specific 6065 h Following Error Window6066 h Following Error Timeout 6068 h Position Window Time606C h Velocity Actual Value Profile Velocity ModeControlword 6040h of Profile Velocity Mode Statusword 6041h of Profile Velocity ModeObject 60FFh Target Velocity 60FF h Target Velocity60FF h Maximum Slippage Integer Mfg-Specific60FD h Digital Inputs Optional Application FE General I/OObject 60FDh Digital Inputs Object 60FEh Digital Outputs 60FE h Digital OutputsWarranty Excellence in Motion