Intelligent Motion Systems DSP-402 manual CANopen DSP402 Application Revision R020507

Page 2

MDrivePlus CANopen Change Log

Date	Revision	Changes

10/06/2006	R100606	Initial Release
12/20/2006	R122006	Added newly supported objects to DSP-402 Implementation

02/05/2007	R020507	Added new object support, broke out DSP 402 to separate document.

The information in this book has been carefully checked and is believed to be accurate; however, no responsibility is assumed for inaccuracies.

Intelligent Motion Systems, Inc., reserves the right to make changes without further notice to any products herein to improve reliability, function or design. Intelligent Motion Systems, Inc., does not assume any liability arising out of the application or use of any product or circuit described herein;

neither does it convey any license under its patent rights of others. Intelligent Motion Systems and	TMare trademarks of Intelligent Motion
Systems, Inc.

Intelligent Motion Systems, Inc.’s general policy does not recommend the use of its products in life support or aircraft applications wherein a failure or malfunction of the product may directly threaten life or injury. Per Intelligent Motion Systems, Inc.’s terms and conditions of sales, the user of Intel- ligent Motion Systems, Inc., products in life support or aircraft applications assumes all risks of such use and indemnifies Intelligent Motion Systems, Inc., against all damages.

CANopen DSP402 Application

Revision R020507

Copyright © 2007 Intelligent Motion Systems, Inc.

All Rights Reserved

Image 2

Contents Forcetm CANopen DSP402 Application Revision R020507 Contents Device Control Profile Position Mode Optional Application FE General I/O List of Figures This Page Intentionally Left Blank Application Guide MDrivePlus CANopen R020507 MDrivePlus Architecture IntroductionCan Message Format Profile Velocity Mode Section Homing Mode SectionProfile Position Mode Section Device ControlObjects and the Object Dictionary Trajectory GeneratorXxxx h Index Name Yes/NoCategory DefaultPDO Mapping RangeIntentionally Left Blank Process Data Object PDO Accessing The MDrivePlus CANopenService Data Object SDO PDO AttributesPDO Mapping PDO Mapping Procedure Consumer PDODefault Mapping Example Consumer PDO Consumer PDO1 RPDO1 1400h Entry Description PDO ObjectsConsumer PDO1 RPDO1 1400h Object Description 1600h Object Description Mapping Parameters1601h Object Description Mapping Parameters Consumer PDO2 RPDO2 1401h Object DescriptionConsumer PDO2 RPDO2 1401h Entry Description 1601h Entry Description Mapping Parameters1602h Object Description Mapping Parameters Consumer PDO3 RPDO3 1402h Object DescriptionConsumer PDO3 RPDO3 1402h Entry Description 1602h Entry Description Mapping Parameters1A00h Entry Description Mapping Parameters Producer PDO1 TPDO1 1800h Entry Description1A00h Object Description Mapping Parameters Producer PDO2 TPDO2 1801h Object DescriptionProducer PDO3 TPDO3 1802h Object Description 1A01h Object Description Mapping Parameters1A01h Entry Description Mapping Parameters Producer PDO3 TPDO3 1802h Entry Description1A02h Entry Description Mapping Parameters Discretes Object 2000h I/O Discretes ConfigAccessibility Codes UnsignedObject 2004h Input Filter Mask Config 2002 h Config Input SwitchesObject 2002h I/O Discretes Config Object 2006h Input Filter Time ms 2004h2006h Input Filter Time 2020h Software Limits as 2010h Analog InputSee Entry Desc Unsigned HardwareSee Table 2031 h Unit Options2032 h Clock Options 2033 h Capture InputObject 2204h Run Current Percent 2204 h Run Current %2205 h Hold Current % Object 2205h Hold Current PercentInteger Options Setting2211h Point TargetAscii Ser. No Factory5002h 5003hState Machine Control and Status wordsState Machine Transitions Internal Object 6040h Controlword 6040 hUnsigned16 Statusword Object 6041h StatuswordBit 5 Quick Stop Active Bit 4 Voltage EnabledBits 12-13 Operation Mode Specific Bit 7 WarningModes of Operation 6060h Mode of Operation±Integer8 Object 6060h Modes of OperationObject 6502h Supported Drive Modes 6061 h Mode of Operation DisplayObject 6061h Modes of Operation Display = Mode Supported = Mode Not Supported Intentionally Left Blank Trajectory Generator Profile Position ModeGeneral Information Input Data DescriptionFunctional Description Set-Point Transmission from Host ComputerControlword 6040h of Profile Position Mode Single Set-Point Mode Move After a Move 6040h Bit 5=06081 h Profile Velocity 607A h Target PositionPossible Integer 6084 h Profile Deceleration 6082 h End Velocity6083 h Profile Acceleration 6086 h Motion Profile Type Object 6086h Motion Profile TypeOutput Data Description Homing ModeInput Data Description Internal StatesHoming Offset 607Ch Statusword 6041h of Homing Mode607C h Homing Offset Possible ± Integer 6098 h Homing Method± Integer Homing Method 6098hMethod 2 Homing on the Positive Limit Switch and Index Pulse Methods 7 to 14 Homing on the Home Switch and Index Pulse Homing on the Negative Home Switch and Index PulseMethods 31 and 32 Reserved Methods 15 and 16 ReservedMethods 17 to 30 Homing without an Index Pulse Method 35 Homing on the Current Position 6099 h Homing SpeedsMethods 33 and 34 Homing on an Index Pulse Homing Speeds 6099hIntentionally Left Blank 6064 h Position Actual Value 6062 h6063 h Position Actual Value Position Control Function6068 h Position Window Time 6065 h Following Error Window6066 h Following Error Timeout Unsigned Mfg-SpecificStatusword 6041h of Profile Velocity Mode Profile Velocity ModeControlword 6040h of Profile Velocity Mode 606C h Velocity Actual ValueInteger Mfg-Specific 60FF h Target Velocity60FF h Maximum Slippage Object 60FFh Target VelocityObject 60FDh Digital Inputs 60FD h Digital InputsOptional Application FE General I/O 60FE h Digital Outputs Object 60FEh Digital OutputsWarranty Excellence in Motion