Juniper Networks SSG 20 manual Using the WebUI

Page 29

3.Launch a serial terminal-emulation program on your workstation. The required settings to launch a console session are as follows:

Baud rate: 9600

Parity: None

Data bits: 8

Stop bit: 1

Flow Control: None

4.If you have not yet changed the default login for the admin name and password, enter netscreen at both the login and password prompts. (Use lowercase letters only. The login and password fields are both case-sensitive.)

For information on how to configure the device with the CLI commands, refer to the Concepts & Examples ScreenOS Reference Guide.

5.(Optional) By default, the console times out and terminates automatically after 10 minutes of idle time. To remove the timeout, enter set console timeout 0.

Using the WebUI

To use the WebUI, the workstation from which you are managing the device must initially be on the same subnetwork as the device. To access the device with the WebUI, perform the following steps:

1.Connect your workstation to the 0/2 — 0/4 port (bgroup0 interface in the Trust zone) on the device.

2.Ensure that your workstation is configured for Dynamic Host Configuration Protocol (DHCP) or is statically configured with an IP address in the 192.168.1.0/24 subnet.

3.Launch your browser, enter the IP address for the bgroup0 interface (the default IP address is 192.168.1.1/24), then press Enter.

NOTE: When the device is accessed through the WebUI the first time, the Initial Configuration Wizard (ICW) appears. If you decide to use the ICW to configure your device, see “Initial Configuration Wizard” on page 63.

The WebUI application displays the login prompt as shown in Figure 14.

Accessing a Device 29

Image 29

Contents SSG 20 Hardware Installation and Configuration Guide Copyright Notice Table of Contents Appendix B Initial Configuration Wizard About This Guide WebUI Conventions OrganizationCLI Conventions Navigational Path and Configuration SettingsObtaining Documentation and Technical Support Hardware Overview Port and Power Connectors Status LED Descriptions Name Color Front PanelSystem Status LEDs Name Color Status Description LAN Port LEDs Name Color Status Description Port DescriptionsLink TX/RXMini PIMs for the SSG Mini Physical Interface Module Port DescriptionsMini PIM LED States on the SSG Type Name Color Description Radio Transceivers Power AdapterBack Panel Grounding Lug USB Port Antennae TypesInstalling and Connecting the Device Before You Begin Installing EquipmentSSG 20 Front-mount Connecting the Power Connecting Interface Cables to a DeviceConnecting a Device to an Untrusted Network Connecting a Device to a NetworkSerial AUX/Console Ports Connecting Mini PIMs to an Untrusted NetworkMicrofilter and Splitter on Your Network Connection Connecting a Device to an Internal Network or a Workstation Wireless Antennae Configuring the Device Using a Console Connection Accessing a DeviceUsing the WebUI WebUI Login Prompt Using TelnetDMZ Default Device SettingsDefault Physical Interface to Zone Bindings Port Label Interface Zone Wireless and Logical Interface BindingsRoot Admin Name and Password Basic Device ConfigurationBridge Group Interfaces Date and TimeManagement Services Administrative AccessManagement Interface Address Default RouteHostname and Domain Name Basic Wireless Configuration Backup Untrust Interface ConfigurationDefault SSG 20-WLAN Configuration WPA-PSK Wireless Authentication and Encryption OptionsWPA WPA2-PSKActivate wireless changes ADSL2/2+ Interface Mini PIM ConfigurationVirtual Circuits PPPoE or PPPoA Static IP Address and Netmask T1 Interface Isdn InterfaceE1 Interface Modem Interface Verifying External Connectivity Basic Firewall ProtectionsResetting a Device to Factory Defaults Page Replacing a Mini-Physical Interface Module Servicing the DeviceRequired Tools and Parts Removing a Mini PIM Removing a Blank FaceplateRemoving a Mini PIM Installing a Mini PIMBottom of Device Upgrading MemoryUnlocking the Memory Module 56 „ Upgrading Memory Specifications Environmental Tolerance PhysicalElectrical Certifications SafetyEMC Emissions EMC ImmunityRJ-45 Connector Pinouts Name Description ConnectorsGND DSRDCD DB-9 Connector Pinouts Name DescriptionDTR RTSPage Initial Configuration Wizard Rapid Deployment Window Administrator Login WindowPhysical Interface Window Wlan Access Point WindowADSL2/2+ Interface Window Adsl Interface Configuration WindowVPI/VCI Fields in Adsl Interface Configuration Window DescriptionT1 Physical Layer Tab Window T1 Interface WindowsFields in T1 Physical Layer Tab Window Description 70 „ Page Cisco Hdlc Option with Cisco Hdlc Tab Window E1 Physical Layer Tab Window E1 Interface WindowsFields in E1 Physical Layer Tab Window Description Field Description Isdn Interface WindowsSPID2 Fields in Isdn Physical Layer Tab Window DescriptionSPID1 Page Eth0/0 Interface Untrust Zone Window 92 Modem Interface WindowEth0/1 Interface DMZ Zone Window Bgroup0 Interface Window Bgroup0 Interface Trust Zone WindowFields in Bgroup0 Interface Window Description Wireless0/0 Interface Trust Zone WindowSsid Fields in Wireless0/0 Interface Window DescriptionInterface Summary Window Physical Ethernet Dhcp Interface Window Wireless Dhcp Interface WindowConfirmation Window Confirmation WindowAdsl IndexVPI/VCI