Juniper Networks SSG 20 manual Installing a Mini PIM, Removing a Mini PIM

Page 53

8.Grasp the screws on each side of the mini PIM faceplate and slide the mini PIM out of the device. Place the mini PIM in the electrostatic bag or on the antistatic mat.

Figure 16: Removing a Mini PIM

9.If you are not reinstalling a mini PIM into the empty slot, install a blank faceplate over the slot to maintain proper airflow.

Installing a Mini PIM

To install a mini PIM, perform the following steps:

1.Attach an ESD grounding strap to your bare wrist and connect the strap to the ESD point on the chassis or to an outside ESD point if the SSG 20 device is disconnected from earth ground.

2.Unplug the power adapter from the device. Verify that the POWER LED is off.

3.Grasp the screws on each side of the mini PIM faceplate and align the notches in the connector at the rear of the mini PIM with the notches in the mini PIM slot in the SSG 20 device. Then slide the mini PIM in until it lodges firmly in the device.

Figure 17: Installing a Mini PIM

CAUTION: Slide the mini PIM straight into the slot to avoid damaging the components on the mini PIM.

4.Tighten the screws on each side of the mini PIM faceplate using a 1/8-inch slotted screwdriver.

5.Insert the appropriate cables into the cable connectors on the mini PIM.

Replacing a Mini-Physical Interface Module 53

Image 53

Contents SSG 20 Hardware Installation and Configuration Guide Copyright Notice Table of Contents Appendix B Initial Configuration Wizard About This Guide WebUI Conventions OrganizationCLI Conventions Navigational Path and Configuration SettingsObtaining Documentation and Technical Support Hardware Overview Port and Power Connectors Status LED Descriptions Name Color Front PanelSystem Status LEDs Name Color Status Description LAN Port LEDs Name Color Status Description Port DescriptionsLink TX/RXMini PIMs for the SSG Mini Physical Interface Module Port DescriptionsMini PIM LED States on the SSG Type Name Color Description Radio Transceivers Power AdapterBack Panel Grounding Lug USB Port Antennae TypesInstalling and Connecting the Device Before You Begin Installing EquipmentSSG 20 Front-mount Connecting the Power Connecting Interface Cables to a DeviceConnecting a Device to an Untrusted Network Connecting a Device to a NetworkSerial AUX/Console Ports Connecting Mini PIMs to an Untrusted NetworkMicrofilter and Splitter on Your Network Connection Connecting a Device to an Internal Network or a WorkstationWireless Antennae Configuring the Device Using a Console Connection Accessing a DeviceUsing the WebUI WebUI Login Prompt Using TelnetDMZ Default Device SettingsDefault Physical Interface to Zone Bindings Port Label Interface Zone Wireless and Logical Interface BindingsRoot Admin Name and Password Basic Device ConfigurationBridge Group Interfaces Date and TimeManagement Services Administrative AccessManagement Interface Address Default RouteHostname and Domain Name Basic Wireless Configuration Backup Untrust Interface ConfigurationDefault SSG 20-WLAN Configuration WPA-PSK Wireless Authentication and Encryption OptionsWPA WPA2-PSKActivate wireless changes ADSL2/2+ Interface Mini PIM ConfigurationVirtual Circuits PPPoE or PPPoA Static IP Address and Netmask T1 Interface Isdn InterfaceE1 Interface Modem Interface Verifying External Connectivity Basic Firewall ProtectionsResetting a Device to Factory Defaults Page Replacing a Mini-Physical Interface Module Servicing the DeviceRequired Tools and Parts Removing a Mini PIM Removing a Blank FaceplateRemoving a Mini PIM Installing a Mini PIMBottom of Device Upgrading MemoryUnlocking the Memory Module 56 „ Upgrading Memory Specifications Environmental Tolerance PhysicalElectrical Certifications SafetyEMC Emissions EMC ImmunityRJ-45 Connector Pinouts Name Description ConnectorsGND DSRDCD DB-9 Connector Pinouts Name DescriptionDTR RTSPage Initial Configuration Wizard Rapid Deployment Window Administrator Login WindowPhysical Interface Window Wlan Access Point WindowADSL2/2+ Interface Window Adsl Interface Configuration WindowVPI/VCI Fields in Adsl Interface Configuration Window DescriptionT1 Physical Layer Tab Window T1 Interface WindowsFields in T1 Physical Layer Tab Window Description 70 „ Page Cisco Hdlc Option with Cisco Hdlc Tab Window E1 Physical Layer Tab Window E1 Interface WindowsFields in E1 Physical Layer Tab Window Description Field Description Isdn Interface WindowsSPID2 Fields in Isdn Physical Layer Tab Window DescriptionSPID1 Page Eth0/0 Interface Untrust Zone Window 92 Modem Interface WindowEth0/1 Interface DMZ Zone Window Bgroup0 Interface Window Bgroup0 Interface Trust Zone WindowFields in Bgroup0 Interface Window Description Wireless0/0 Interface Trust Zone WindowSsid Fields in Wireless0/0 Interface Window DescriptionInterface Summary Window Physical Ethernet Dhcp Interface Window Wireless Dhcp Interface WindowConfirmation Window Confirmation WindowAdsl IndexVPI/VCI