Juniper Networks 5000 SERIES manual 48V COMThumbscrew Power

Page 26

Chapter 2 Installing the Device

The DC power supply, power switch, grounding screw, and terminal blocks, are located on the faceplate of the power supply unit.

-48V -48V

COMThumbscrew

Power

LED

DC Power

Terminal Block

Grounding

Screw

Power Switch

Warning: You must shut off current to the DC feed wires before connecting the wires to the power supplies. Also, make sure that the power switch is in the off position.

To connect the DC power supply to a grounding point at your site:

1.Remove the hex nut on the grounding screw.

2.Place the ground lug on the screw and tighten the hex nut securely.

3.Connect the other end of the grounding lug wire to a grounding point at your site.

To connect DC power feeds to the terminal blocks:

1.Loosen the retaining screws on each terminal block.

2.Insert the 0V DC (positive voltage) return wire into the center COM connector and the -48V DC power feed wire into either the left or right connector.

3.Fasten the screws over the connectors.

4.Turn the power switches on.

Note: If there are multiple power supplies in the NetScreen-5000 Series device and any of them are off, the Alarm LED on the Management Module glows solid red. This alarm indicates that maximum system stability requires all installed power supplies to be operational.

18	User’s Guide

Image 26

Contents NETSCREEN-5000 Series Copyright Notice Language Contents Language Contents Table of Contents Servicing the Device Index Table of Contents Viii Preface Guide OrganizationJuniper Networks Netscreen Publications Command Line Interface CLI ConventionsSet admin user name1 password xyz Overview1 NETSCREEN-5000 Series NetScreen-5200NetScreen-5400 Power Supplies DC Power Supply NetScreen-5200 Power RecommendationsNetScreen-5400 Power Recommendations AC Power Supply FAN Modules5000-M Management Module Management ModulesNETSCREEN-5000 Modules 5000-M2 Management Module NetScreen-5000 ModulesSecure Port Modules 5000-8G SPM5000-2G24FE SPM Overview User’s Guide Installing the Device General Installation Guidelines Equipment Rack Installation GuidelinesNetScreen-5200 Front and Rear Mount Mounting the NETSCREEN-5000 SeriesNetScreen-5200 Mid-Mount NetScreen-5400 Front MountInstalling and Connecting the AC Power Supply Installing and Wiring a DC Power Supply48V COMThumbscrew Power Connecting the NETSCREEN-5000 Series to a Router or Switch Establishing AN HA ConnectionInstalling the Device User’s Guide Configuring the Device Operational Modes Transparent ModeRoute Mode NetScreen-5200 Interfaces NETSCREEN-5000 InterfacesConfigurable Interfaces NetScreen-5400 InterfacesPerforming Initial Connection and Configuration Establishing a Terminal Emulator ConnectionUpgrading the Firmware During the Boot Process Viewing Current Interface Settings Changing Your Admin Name and PasswordSetting Port and Interface IP Addresses Setting the IP Address of the Management InterfaceSetting the IP Address for the Trust Zone Interface Setting the IP Address for the Untrust Zone InterfaceAllowing Outbound Traffic Starting a Console Session Using TelnetConfiguring the Device for Telnet and Webui Sessions Telnet Starting a Console Session Using DialupEstablishing a GUI Management Session Get chassis Configuring the Chassis AlarmHttp//10.100.2.183 Get interface Get interface aggregate1 Configuring Aggregate InterfacesSet interface string zone zonename Using CLI Commands to Reset the Device Following CLI command unset admin device-resetPress the y key Following message appears Servicing the Device Replacing a DC Power Supply Removing and Reseating ModulesReplacing AN AC Power Supply Replacing the FAN TrayConnecting and Disconnecting Gigabit Ethernet Cables Removing and Installing a MINI-GBIC Transceiver Servicing the Device User’s Guide Specifications NETSCREEN-5200 Attributes Electrical SpecificationEnvironmental Specification NETSCREEN-5400 AttributesNebs Certifications Safety CertificationsConnectors EMI CertificationsAppendix a Specifications User’s Guide Port Descriptions and LED Status B Module Port Descriptions MGTStatus LED States Interpreting Status LEDs for the Management ModulesModule LED Descriptions Interpreting Status LEDs for the Secure Port Module Interpreting Ethernet Port Status LEDs for All ModulesPower Supply Leds Interpreting Power Supply LED Status for the NetScreen-5200Interpreting Power Supply LED Status for the NetScreen-5400 Single SPM InstalledFAN LED Index User’s Guide Table des matières Chapitre Entretien de l’unité Index 103 Table des matières Xii Manuel de l’utilisateur Préface Organisation DU ManuelSet admin user nom1 password xyz Publications Juniper Networks NetscreenPrésentation générale Série DE Produits NETSCREEN-5000 Unité NetScreen-5200Unité NetScreen-5400 Blocs D’ALIMENTATION Bloc d’alimentation CC DELBloc d’alimentation CA Modules DE VentilationModule de gestion 5000-M Modules de gestionModules NETSCREEN-5000 Module de gestion 5000-M2 Modules NetScreen-5000Modules de ports sécurisés SPM 5000-8GSPM 5000-2G24FE Chapitre 1 Présentation générale Manuel de l’utilisateur Installation de l’unité Instructions D’INSTALLATION Générales Instructions D’INSTALLATION DE LA Baie DE ÉquipementMontage avant et arrière de l’unité NetScreen-5200 Montage DE L’UNITÉ DE LA Série NETSCREEN-5000Montage à mi-hauteur de l’unité NetScreen-5200 Montage frontal de l’unité NetScreen-5400Installation ET Connexion DU Bloc Dalimentation CA Installation ET Raccordement D’UN Bloc ’ALIMENTATION CDCOM Établissement D’UNE Connexion HA Chapitre 2 Installation de l’unité Manuel de l’utilisateur Configuration de l’unité Modes DE Fonctionnement Mode TransparentMode Route Interfaces NetScreen-5200 Interfaces NETSCREEN-5000Interfaces configurables Interfaces NetScreen-5400Exécution DE LA Connexion ET DE LA Configuration Initiales Établissement d’une connexion d’émulateur de terminalChapitre 3 Configuration de l’unité Affichage des paramètres d’interface actuels Configuration des adresses IP de port et d’interfaceConfiguration de l’adresse IP de l’interface de gestion Set interface mgt ip adrip/masqueGet interface ethernet2/2 Get interface mgtSet interface ethernet2/2 ip adrip/masque Set interface ethernet2/3 ip adrip/masque Démarrage d’une session de console à l’aide de TelnetAutorisation du trafic sortant Telnet Configuration DE L’ALARME DE Châssis Configuration D’INTERFACES Agrégées Set interface chaîne zone nomdelazoneSérie de produits NetScreen-5000 Appuyez sur la touche y Le message suivant s’affiche Entretien de l’unité Retrait ET Réinstallation DES Modules Remplacement D’UN Bloc D’ALIMENTATION CCRemplacement D’UN Bloc D’ALIMENTATION CA Remplacement DU Bloc DE VentilationConnexion ET Déconnexion DES Câbles Gigabit Ethernet Retrait ET Installation D’UN Transmetteur MINI-GBIC Chapitre 4 Entretien de l’unité Manuel de l’utilisateur SpécificationsA Spécifications Électriques Attributs DE L’UNITÉ NETSCREEN-5200Attributs DE L’UNITÉ NETSCREEN-5400 Spécifications EnvironnementalesCertifications EMI Certifications NebsCertifications DE Conformité ConnecteursAnnexe a Spécifications Manuel de l’utilisateur Série de produits NetScreen-5000 Description DES Ports DES Modules Etats DES DEL D’ÉTAT Interprétation des DEL d’état des modules de gestionDescription DES DEL DES Modules Interprétation des DEL d’état des modules de ports sécurisés Un seul SPM installé DEL DES Blocs D’ALIMENTATIONDEL DE Ventilation FAN Nombres 104 Manuel de l’utilisateur