Huawei Aolynk DR811, Aolynk DR814 user manual Zipb setting

Page 40

User Manual

 

Aolynk DR811/DR814 ADSL2+Broadband Router

4 Web-based Management

Figure 4-28 ZIPB setting

This page allows you to:

Enable/disable the ZIPB mode.

Perform advanced ZIPB configurations.

If the ZIPB is currently disabled, you may click the button to enable it. If the

ZIPB is currently enabled, you may click the button to disable it.

To select which of your LAN computers will use the public IP address, click on the drop-down list below Choose which computer will use the public IP address, position the cursor over the entry and left-click to select a LAN computer, and then click

the button.

To perform advanced ZIPB configurations, proceed according to the following steps:

Select the LAN interface that ZIPB will run on: click on the LAN interface drop down list and select an interface.

Select the WAN interface that ZIPB will run on: click on the WAN interface drop down list and select an interface.

Once you have configured ZIPB, click the button.

&Note:

Make ensure that ZIPB is disabled before you configure ZIPB. Edit the configurations and click OK, the new configuration will take effect after you enable ZIPB. Configuration changes on ZIPB will not be kept permanently, so you need to configure it again whenever the Router is restarted. In this way, remember to renew the IP address of the ZIPB host first.

37

Image 40
Contents Huawei Aolynk DR811/DR814 ADSL2+Broadband Router All Rights Reserved Trademarks Table of Contents IP Addresses, Network Masks, and Subnets Product Overview IntroductionsModel Difference Front View AppearanceStatus Description Interface Quantity Connector Description FeaturesRear View Parts Check Interface QuantityOverview Connecting Your DeviceSteps Finish Accessing the Web Pages Getting Started with the Web PagesLAN Settings button Web Page Layout Commonly Used Buttons Button FunctionTesting Your Setup BehaviorOption Default Setting Explanation/Instruction Default Device SettingsEnabled with Quick Setup Web-based ManagementWAN Setting Open the WAN Connection ConfigurationWAN setting DNS Relay LAN Setting DNS relayLAN setting Dhcp Route Aolynk DR811/DR814 ADSL2+Broadband Router 12Create routes Security Interface Labeled Enabled/Disabled Aolynk DR811/DR814 ADSL2+Broadband Router DMZ Configuration 19Add a security interface Security Policy Trigger Definition24 Add trigger Aolynk DR811/DR814 ADSL2+Broadband Router 11 IDS 25Delete trigger Click the button to delete this trigger26 IDS setting Sntp27 Sntp setting Zipb28 Zipb setting Password Remote AccessRestart Router 32 RestartConfiguration Backup/Restore Aolynk DR811/DR814 ADSL2+Broadband Router Upgrade 37Restore configurationStatus 39 Status 20 Log PVC Scan 41 LogSave Configure Configuring Your Computers Configuring Ethernet PCsBefore You Begin Windows XP PCsWindows 2000 PCs Windows Me PCs Windows 95, 98 PCsWindows NT 4.0 Workstations Assigning Static Internet Information to Your PCs Connecting a Computer to the USB Port by a USB cable Configuring a PC Connected by USB PortInstalling the USB Driver 2Found new hardware New hardware installed and ready to use Configuring IP Properties on PC Connected by USB Port IP Addresses IP Addresses, Network Masks, and SubnetsStructure of an IP Address Network Classes Subnet MasksClass Field1 Field2 Field3 Field4 Aolynk DR811/DR814 ADSL2+Broadband Router Service Configuration Configuration OverviewPureBridge ConnectionPureBridgeDHCP/StaticIP IPoAPPPoA PPPoEPPPoE Troubleshooting Suggestions TroubleshootingProblem Troubleshooting Suggestion To see if the Adsl line is connected correctly Ping Diagnosing Problem Using IP UtilitiesPing Nslookup NslookupAppendix Glossary Dhcp server DomainName DownloadHost HubInternet IntranetNetwork Network mask PacketPort Protocol Remote RJ-11RJ-45 RoutingSubnet Subnet maskWeb Web browserWeb site