GarrettCom manual DIN-Rail Mounting the Magnum 6KQ

Page 31

Magnum 6KQ Managed Field Switch Installation and User Guide

(04/07)

fiber optic segment.

3.Find the Transmit (TX) and Receive (RX) markings on the SFP transceiver to verify the top side of it. Some of the transceiver marks arrow sign for up.

4.Position the SFP transceiver correctly before insertion, and then insert the SFP

transceiver carefully, until the transceiver connector snap into the place in the socket connector.

5.Connect the Transmit (TX) port on the Magnum PM to the Receive (RX) port of the remote device. Connect the Receive (RX) port on the PM to the Transmit (TX) port of the remote device.

The LINK LED on the front of the PM will illuminate and turn Green, when a proper connection has been established at both ends (and when power is ON in the unit). If LINK is not lit or OFF after cable connection, the normal cause is improper cable

polarity. Swap the fiber cables at the PM connector and also check the connectivity on the target device to remedy this situation.

Reconfigure or reboot both the device if required.

If connected properly, you can check via (MNS-6K)software too for verification the validity of SFP Gigabit ports.

Make sure Rel 3.6 or higher firmware is loaded on the 6KQ switches to support the SFP transceivers.

3.3DIN-Rail Mounting the Magnum 6KQ

The Magnum 6KQ is designed for use in a “factory floor” industrial

environment. It is available with optional DIN-Rail brackets to mount it securely in a metal factory floor enclosure, maintained vertically for proper convection cooling of the unit. The Magnum 6KQ requires one DIN-Rail mounting clip or latch for secure mounting. These may be ordered as Model # DIN-RAIL-6KQ. See a 6KQ viewed from the side, at the left, with model DIN-RAIL-6KQ in place on the unit.

www . GarrettCom . com

25

Image 31

Contents Managed Field Switch Trademarks Canadian Emission Contacting GarrettCom, IncIntroduction Table of ContentsInstallation Introduction Magnum 6KQ Managed Field Switch Port Modules35Troubleshooting Overview Magnum LineMaximum 10 Mbps Ethernet Segment Lengths Technical SpecificationsPerformance Network Standards and Compliance, hardwareManagement Console connector Fiber Multi-mode connector types supportedFiber Single-mode connector types Alarm Relay Contacts6KQ Mounting DC-DUAL Power Source OptionalAgency Approvals and Standards Compliance Ordering Information Www . GarrettCom . com Introduction Inspecting the Package and Product Product Description Magnum 6KQ Field Switch Www . GarrettCom . com 6KQ4-MTRJ F/Habove 6KQ4MLC or -SLC below SFF Fiber Port ModulesFour-Port Copper Module, 6KQ4-RJ45 Two-Port Fiber Modules, 2@ 100Mb fiber SFP Gigabit 1000Mbps port modules Two -Port 10 Mb mm Fiber ST Modules@ 10/100/1000Mb RJ-45 + 1@ 1000Mb SFP Frame Buffering and Flow Control Packet Prioritization, 802.1p QOSWeb-browser, at ftp//ftp.garrettcom.com Managed Network Software MNS-6K for Magnum 6KQ-Series„ Managed switching for high performance Ethernet LANs Features and Benefits„ Features Fiber-Built-In Applications Example 1 Magnum 6KQ Switch for a Industrial Application4a- The industrial factory floor application with Magnum 6KQ Snmp Locating Magnum 6KQ Switches Copper Connecting Ethernet MediaConnecting Fiber Optic ST-type, twist-lock Ieee Standard Media Type Max. Distance FiberMedia Ieee Standard Connecting Fiber Optic SC-type, Snap-InConnecting Single-Mode Fiber Optic Connecting Twisted Pair CAT3, CAT5, Unshielded or ShieldedWww . GarrettCom . com Gigabit SFP Small Form-factor Pluggable Optical Transceivers Side View Duplex LC connector Front view6a Connecting Fiber Optic Cable to SFP Transceivers DIN-Rail Mounting the Magnum 6KQ Mounting Dimensions for 6KQ with metal brackets Powering the Magnum 6KQ Managed Field Switch Relay Contacts Female Connector Pin Name Description Dir 6KQ Port Module 6KPM InstallationMale Connector Filtering and Forwarding Switching FunctionalityACT Status LEDsAuto-CrossMDIX and Auto-negotiation, for RJ-45 ports PWRThis manual to access the 6K-MNSRel 3 Software user guide Flow-control, Ieee 802.3x standard Power Budget Calculations for 6KQ PM’s with Fiber MediaMLC F10ST6KPM Module Description Introduction Magnum 6KQ Managed Field Switch Port Modules1a 6KQ2-10ST, 2@10Mb multi-mode FX-ST twist lock Module KQF-2MSC, 2@100Mb multi-mode FX-SC snap-in Fiber connector 5 6KQ4-MT, 4 @100Mb multi-mode FX , Mtrj Small-Form-factor FX-SC-type, snap-in@ 10/100Mbps RJ-45 @100Mb multi-mode FX , Mtrj Small-FF 7 6KQ4-MLC, 4 ports @ 100Mbps multi-mode LC connector SFF9 6KQ4-RJ45 Twisted Pair, 10/100Mb, 4-Port Mbps RJ-45 ConnectorPoE LEDs Summary SFPs, Gigabit 1000Mbps port modules Before Calling for Assistance 12 6KQ-BLNKShipping and Packaging Information When Calling for AssistanceReturn Material Authorization RMA Procedure No Problem FoundAppendix a Warranty Information B2.0 -48VDC, 24VDC and 125VDC POWER, Theory of Operation Standard 6KQ DC Power Input Terminal Block -, GND, +B3.0 Applications for DC Powered Ethernet Switches B4.1 UL Requirements for DC-powered units B4.0 6KQ, -48V, 24, 125VDC InstallationB5.0 Operation B6.0 TroubleshootingC5.0 Installation C4.0 Features and Benefits of the DUAL-SOURCE DesignExample Magnum 6KQ-24VDC or Magnum P6KQ-125VDC Or Dual-Src125V-SwitchC5.1 UL Requirements C6.0 Ordering Information