GarrettCom Magnum 6KQ manual 12 6KQ-BLNK, Before Calling for Assistance

Page 49

Magnum 6KQ Managed Field Switch Installation and User Guide

(04/07)

5.2.126KQ-BLNK

The 6KQ-BLNK is a blank face plate or cover plate that must be installed in any empty 6KQ PM slot to maintain proper cooling air flow, safety, etc. Two screws underneath the front panel hold the 6KQ-BLNK in place.

6.0TROUBLESHOOTING

All Magnum Ethernet products are designed to provide reliability and

consistently high performance in all network environments. The installation of a Magnum 6KQ Switch is a straightforward procedure (see INSTALLATION, Section 3.0). The operation is also straightforward and is discussed in Section 4.

Should problems develop during installation or operation, this section is intended to help locate, identify and correct these types of problems. Please follow the suggestions listed below prior to contacting your supplier. However, if you are unsure of the procedures described in this section or if the Magnum 6KQ Switch is not performing as expected, do not attempt to repair the unit; instead contact your supplier for assistance or contact GarrettCom Customer Support.

6.1Before Calling for Assistance

1.If difficulty is encountered when installing or operating the unit, refer back to the Installation Section of the applicable chapter of this manual. Also check to make sure that the various components of the network are interoperable.

2.Check the cables and connectors to ensure that they have been properly connected and the cables/wires have not been crimped or in some way impaired during installation. (About 90% of network downtime can be attributed to wiring and connector problems.)

3.Make sure that DC power is properly attached to each Magnum 6KQ Switch unit. Use the PWR LEDs to verify each unit is receiving power.

4.If the problem is isolated to a network device other than the Magnum 6KQ Switch product, it is recommended that the problem device be replaced with a known good device. Verify whether or not the problem is corrected. If not, go to Step 5 below. If the problem is corrected, the Magnum 6KQ Switch and its associated cables are functioning properly.

5.If the problem continues after completing Step 4 above, contact your supplier of the Magnum 6KQ Switch unit or if unknown, contact GarrettCom, Inc.by fax, phone or email (support@garrettcom.com) for assistance.

www . GarrettCom . com

43

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Managed Field Switch Trademarks Canadian Emission Contacting GarrettCom, IncInstallation Table of ContentsIntroduction Magnum 6KQ Managed Field Switch Port Modules35 IntroductionTroubleshooting Overview Magnum LinePerformance Technical SpecificationsNetwork Standards and Compliance, hardware Maximum 10 Mbps Ethernet Segment LengthsFiber Single-mode connector types Fiber Multi-mode connector types supportedAlarm Relay Contacts Management Console connector6KQ Mounting DC-DUAL Power Source OptionalAgency Approvals and Standards Compliance Ordering Information Www . GarrettCom . com Introduction Inspecting the Package and Product Product Description Magnum 6KQ Field Switch Www . GarrettCom . com 6KQ4-MTRJ F/Habove 6KQ4MLC or -SLC below SFF Fiber Port ModulesFour-Port Copper Module, 6KQ4-RJ45 Two-Port Fiber Modules, 2@ 100Mb fiber SFP Gigabit 1000Mbps port modules Two -Port 10 Mb mm Fiber ST Modules@ 10/100/1000Mb RJ-45 + 1@ 1000Mb SFP Frame Buffering and Flow Control Packet Prioritization, 802.1p QOSWeb-browser, at ftp//ftp.garrettcom.com Managed Network Software MNS-6K for Magnum 6KQ-Series„ Managed switching for high performance Ethernet LANs Features and Benefits„ Features Fiber-Built-In Applications Example 1 Magnum 6KQ Switch for a Industrial Application4a- The industrial factory floor application with Magnum 6KQ Snmp Locating Magnum 6KQ Switches Connecting Fiber Optic ST-type, twist-lock Connecting Ethernet MediaIeee Standard Media Type Max. Distance Fiber CopperConnecting Single-Mode Fiber Optic Connecting Fiber Optic SC-type, Snap-InConnecting Twisted Pair CAT3, CAT5, Unshielded or Shielded Media Ieee StandardWww . GarrettCom . com Gigabit SFP Small Form-factor Pluggable Optical Transceivers Side View Duplex LC connector Front view6a Connecting Fiber Optic Cable to SFP Transceivers DIN-Rail Mounting the Magnum 6KQ Mounting Dimensions for 6KQ with metal brackets Powering the Magnum 6KQ Managed Field Switch Relay Contacts Female Connector Pin Name Description Dir 6KQ Port Module 6KPM InstallationMale Connector Filtering and Forwarding Switching FunctionalityAuto-CrossMDIX and Auto-negotiation, for RJ-45 ports Status LEDsPWR ACTThis manual to access the 6K-MNSRel 3 Software user guide Flow-control, Ieee 802.3x standard Power Budget Calculations for 6KQ PM’s with Fiber MediaMLC F10ST6KPM Module Description Introduction Magnum 6KQ Managed Field Switch Port Modules1a 6KQ2-10ST, 2@10Mb multi-mode FX-ST twist lock Module KQF-2MSC, 2@100Mb multi-mode FX-SC snap-in Fiber connector 5 6KQ4-MT, 4 @100Mb multi-mode FX , Mtrj Small-Form-factor FX-SC-type, snap-in@ 10/100Mbps RJ-45 @100Mb multi-mode FX , Mtrj Small-FF 7 6KQ4-MLC, 4 ports @ 100Mbps multi-mode LC connector SFF9 6KQ4-RJ45 Twisted Pair, 10/100Mb, 4-Port Mbps RJ-45 ConnectorPoE LEDs Summary SFPs, Gigabit 1000Mbps port modules Before Calling for Assistance 12 6KQ-BLNKReturn Material Authorization RMA Procedure When Calling for AssistanceNo Problem Found Shipping and Packaging InformationAppendix a Warranty Information B2.0 -48VDC, 24VDC and 125VDC POWER, Theory of Operation Standard 6KQ DC Power Input Terminal Block -, GND, +B3.0 Applications for DC Powered Ethernet Switches B4.1 UL Requirements for DC-powered units B4.0 6KQ, -48V, 24, 125VDC InstallationB5.0 Operation B6.0 TroubleshootingC5.0 Installation C4.0 Features and Benefits of the DUAL-SOURCE DesignC5.1 UL Requirements Or Dual-Src125V-SwitchC6.0 Ordering Information Example Magnum 6KQ-24VDC or Magnum P6KQ-125VDC
Top Page Image Contents