GarrettCom 6K25e manual 1a Removing Chassis Cover

Page 37

Magnum 6K25e Gigabit Fiber Switch

Installation and User Guide (10/07)

assembled together with the help of 22 Philips-head screws. There are 7 screws located on the front-bottom and rear-top of the unit and four screws each on the sides. Remove these screws. Once these are removed, the top cover is easily lifted off the chassis base. When the chassis top cover has been removed, the interior of the unit is exposed.

Figure 3.5.1a: Removing Chassis Cover

Caution: Be careful not to disturb the power supply.

Looking down into the Magnum 6K25e unit, notice that there are individual PM installation spaces and female latch(white) connectors provided on the main board along with four stand-off’s for each 6KPM card position. (See Figure 3.5.1b).

Figure 3.5.1b: Magnum 6K25e, Top view without chassis cover

Step 3. Remove front panel face plate retaining screws

There are four PM slots (A, B, C and D) located on the front of the chassis cover. Looking into the vertical placed Chassis cover of the unit, there are three brackets with retaining screws (#256 flat head ) which hold each PM Face plate card slot securely. These six screws shown in the picture below are used to secure a PM face plate in position, but unscrew only four of the screws as shown in Fig. below. These screws are also used to secure the individual 6KPM cards screen plate which can be subjected to significant forces from the attached cables. (See Figure 3.5.1c)

Figure 3.5.1c: Top View – 6KPM retaining screws hold Face Plate

www . GarrettCom . com

31

Image 37
Contents Gigabit Fiber Switch Trademarks Canadian Emission Contacting GarrettCom, IncIntroduction Table of ContentsRevisions 6K25E Managed Fiber Switch Port ModulesMagnum Line Performance Technical SpecificationsNetwork Standards and Compliance, hardware Maximum 10 Mbps Ethernet Segment LengthsFiber Single-mode connector types Fiber Multi-mode connector types supportedManagement Console connector Power Supply InternalNebs Testing and Certification Nebs certified Alarm Contact OptionalPer-port MDI or Mdix on RJ-45 Agency ApprovalsOrdering Information 6K PoE Modules with 48VDC Pass-Through For Gigabit module configuration options6K PoE Modules with 48VDC Power Inside Introduction Inspecting the Package and Product Product Description Magnum 6K25e Managed Fiber SwitchWww . GarrettCom . com Eight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb fiber Magnum 6K25e and 6K25eR chassisPort modules for the Magnum 100Mb fiber eightEight-Port Copper Module, 6K8-RJ45 The 6K25e-Series’s8-port New PoEPower Inside, model PI6KP8-45RJ MDIX, 10/100Mb 8-port Per the IEEE802.3af PoE Four-Port 10 Mb mm Fiber ST Modules Gigabit 1000Mbps port modules Frame Buffering and Flow Control Packet Prioritization, 802.1p QOSWeb-browser, at ftp//ftp.garrettcom.com Managed Network Software MNS-6K for Magnum 6K25e-Series„ Features Fiber-Built-In „ Managed switching for high performance Ethernet LANs„ Nebs and Etsi tested and certified „ SFP Gigabit module being supported on Slot D „ RJ-45 ports are MDI/MDIX supportedApplications 6K 25e Locating Magnum 6K25e Switches InstallationConnecting Fiber Optic ST-type, twist-lock Connecting Ethernet MediaIeee Standard Media Type Max. Distance Port Module Fiber CopperConnecting Single-Mode Fiber Optic Connecting Fiber Optic SC-type, Snap-InMedia Ieee Standard Media Ieee Standard Gigabit SFP Small Form-factor Pluggable Optical Transceivers Side View Duplex LC connector Front viewSFP-SX SFP-LX10 SFP-LX25 SFP-ZX40 SFP-ZX70 Table-Top or Shelf Mounting1 Mountings for Magnum 6K25e units rack-mounted in a frame Rack-mounting for 19 Retma racks, regular Magnum 6K25esRack-mounting, Reverse version of the Magnum 6K25es Powering the Magnum Managed Fiber SwitchWww . GarrettCom . com Preparation for Installing and Removing 6KPMs 6K25e Port Module 6KPM InstallationRemove Chassis Cover 1a Removing Chassis Cover Installing 6KPM Cards in the Magnum 6K25e Uplink 2f Securely latching up 6KPM Cards into a Magnum 6K25e Removing 6KPM Cards Console DB-9 Port Connecting the Console Terminal to Magnum 6K25e ManagementRemove 6KPM Card Switching Functionality Pin Signal DescriptionDB-9 Console port connector 1 RS-232 DB-9 Console Com port Serial port pin assignmentsUp-link MDI-MDIX on RJ-45 port modules, for port 1 only Status LEDsPWR ACTAuto-CrossMDIX and Auto-negotiation, for RJ-45 ports Flow-control, Ieee 802.3x standard F10ST Introduction Magnum 6K25e Managed Fiber Switch Port Modules 6KPM Module Description 1b 6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module @10Mb @100Mb Multi-mode FX-ST twist 1c 6KP4Lock Module Mode SC-type connectors. It Provides an advantage Mode 100Mbps fiber opticFiber functions in one Module of the 6K25e Switch Transceivers all in one module. ThisWww . GarrettCom . com Activity FULL/HALF Port@ 100Mbps Multi-Mode Fiber portLink Form Factor 9 6KP8-RJ45 Twisted Pair, 10/100Mb 8-Port Option in one 6K-unit Fig. the top 8-RJ45 PoE LEDs Summary10/100 GBIC-SXSC Gigabit fiber1000Mb, multi-mode SC Connector Before Calling for Assistance 14 6KM-BLNKReturn Material Authorization RMA Procedure When Calling for AssistanceShipping and Packaging Information No Problem FoundSpecifications for Magnum 6K25E SWITCHES, DC Power Appendix B Internal DC Power Supply OptionsB3.0 Applications for DC Powered Switches Magnum 6K25es. see figure at right B4.0 InstallationB4.1 UL Requirements for DC-powered units Appendix C Internal DC Dual-Source Power OptionB7.0 Troubleshooting B5.0 OperationC5.0 Installation C4.0 Features and Benefits of the DUAL-SOURCE DesignC6.0 Ordering Information C5.1 UL RequirementsExample Magnum 6K25eR-48VDC Example Magnum 6K25eR-24VDC or Magnum 6K25eR-125VDCOperation C7.0